juanvm

Hello :) I downloaded V3.96 couple of days ago, but had to revert to V3.93 because I was unable to assign axis, like it did not recognised the Zaitek pro yoke, I'm using Windows 7, so V3.93 works fine. I installed V3.96 again today and (1) it did not recognised my previous Fsuipc configation settings, so made a copy of it, erased it and Fsuipc created a new one (2) started Fs9 loaded cessnna opened Fsuipc scanned for the throttle axis and found B axis Z but rescaned again with B axis U and assined it to throttle 1 for fsuipc calibration, and calibrated the throttle 1 in page 3, exited fsuipc, tested axis, was ok went back to fsuipc to assing other axis, but no luck, I hit rescan, moved some axis levers but it seen that the controller is not recognized by Fsuipc. Even with simple configuration: [JoyNames] AutoAssignLetters=Yes 0=Saitek Pro Flight Throttle Quadrant 1=Saitek Pro Flight Yoke 2=Saitek Pro Flight Rudder Pedals A=Saitek Pro Flight Throttle Quadrant B=Saitek Pro Flight Yoke C=Saitek Pro Flight Rudder Pedals [General] UpdatedByVersion=3960 WindSmoothing=No AutoTaxiWind=No PropTaxiWind=No TimeSetMode=Partial WhiteMessages=No ThrottleSyncAll=No GraduatedVisibility=No LowerVisAltitude=0 UpperVisAltitude=25000 UpperVisibility=6000 GenerateCirrus=No WindShearSharp=No UpperWindGusts=Yes ExtendMetarMaxVis=No CorrectVSsign=No MouseWheelTrim=No MouseWheelTrimSpeed=1 BrakeReleaseThreshold=75 AxisInterceptIfDirect=No DontResetAxes=No DisconnTrimForAP=No ZeroElevForAPAlt=No AutoClearWeather=Yes ExtendTopWind=No WindSmoothness=5 SmoothPressure=No PressureSmoothness=5 SmoothVisibility=No VisibilitySmoothness=2 MaxSurfaceWind=0 WindLimitLevel=200 WindDiscardLevel=400 WindAjustAltitude=No WindAjustAltitudeBy=2000 MinimumVisibility=0 MaximumVisibilityFewClouds=0 MaximumVisibility=0 MaximumVisibilityOvercast=0 MaximumVisibilityRainy=0 OneCloudLayer=No ThinClouds=No ThinThunderClouds=No CloudThinness=1000 ThunderCloudThinness=10000 CloudTurbulence=No CloudIcing=No WindTurbulence=No SuppressAllGusts=No ExternalOptionControl=Yes AutoTuneADF=No KeepFS98CloudCover=No ShowPMcontrols=No MagicBattery=No RudderSpikeRemoval=No ElevatorSpikeRemoval=No AileronSpikeRemoval=No ReversedElevatorTrim=No StopAutoFuel=No TrapUserInterrupt=Yes NavFreq50KHz=No ClockSync=No SmoothIAS=Yes SetVisUpperAlt=No VisUpperAltLimit=6000 MaxIce=-4 MinIce=-4 WindSmoothingDelay=0 WindSmoothAirborneOnly=No LimitWindVariance=No VisSmoothingDelay=0 VisSmoothAirborneOnly=No TrafficControlDirect=Yes SuppressCloudTurbulence=No SuppressWindTurbulence=No SpoilerIncrement=512 JoystickTimeout=15 ZapSound=firework ShortAircraftNameOk=No UseProfiles=No TCASid=Flight TCASrange=40 TrafficScanPerFrame=10 AxisCalibration=No CentredDialogue=Yes ShowMultilineWindow=Yes SuppressSingleline=No SuppressMultilineFS=No ClearWeatherDynamics=Yes OwnWeatherChanges=No FixWindows=No FixControlAccel=No WeatherReadInterval=4 MoveBGLvariables=Yes TimeForSelect=4 WeatherReadsFast=No MainMenu=&Modules SubMenu=&FSUIPC ... [JoystickCalibration] AllowSuppressForPFCquad=Yes ExcludeThrottleSet=Yes ExcludeMixtureSet=Yes ExcludePropPitchSet=Yes SepRevsJetsOnly=No ApplyHeloTrim=No UseAxisControlsForNRZ=No FlapsSetControl=0 FlapDetents=No ReverserControl=66292 Reverser1Control=66422 Reverser2Control=66425 Reverser3Control=66428 Reverser4Control=66431 MaxThrottleForReverser=256 AileronTrimControl=0 RudderTrimControl=0 CowlFlaps1Control=0 CowlFlaps2Control=0 CowlFlaps3Control=0 CowlFlaps4Control=0 MaxSteerSpeed=60 Throttle=-16125,16125/8 !1= [buttons] ButtonRepeat=20,10 Meanwhile will have to go back to V3.93 Thanks :)

Hello Pete :) I posted the following in the Saitek Pro Yoke support forum: "I had set most of my FS9 aircraft's using FSUIPC V3.93 with the Saitek Pro Yoke, pedals and quadrant, but when I calibrate the throttles for the Wilco Feelthere airbus A320, for example, the auto pilot throttle control does not work (will funtion manually but not Auto throttle). Someone had been able to program with this aircrafts without problems?????????????" I did a search here and found a person with a problem with the A320 but his solution does not work with my Saitek controls. Appreciate any help. Thanks :?