dazzan

I have a problem with assigning functions to a button. When I asign a function on button press and on button release, the button release function only works when cycling the button. Depressing alone does not activate the function defined on button release. I want to define a switch for gear up and gear down. With the toggle function in FSUIPC it is the same, just depressing makes no function, I have to cycle again to get the depress function. I use a keyboard encoder card on a remote pc sending via wideclient the keyboard commands to fsuipc on server computer. I noticed that with all FSUIPC versions I could test so far. Thanks Gilles

Hi Pete, I have defined and calibrated the flaps in FSUIPC 3.847 with FS2004. But I need to run another driver for the throttle that tries also to set the flaps. So the problem is the flaps setting from FSUIPC 3.847 is overruled by that driver trying to keep flaps 0. In Fsuipc 4 with FSX there is a command axisintercepts=yes, with that setting everything works, Fsuipc is not overruled. I tried that setting with FSUIPC 3.847 and FS2004 but it seems not to know that command. Or is there another possibility for FSUIPC to be the only considered source for an axis? Many thanks for helping Gilles

Hi Pete, How it is possible to run the projectmagenta CDU program and the Thomas Richter electronic checklist on one hardware CDU. Are there offsets to switch between the programs? Many thanks Gilles

Hi I was looking for the offsetes in FSUIPC 407 SDK. But I am sorry I did not remember that the second columns were bytes. You understood my initial question perfectly, thanks. Thanks Gilles

Hi Pete Does for example 0318 4 mean offset 0318 bit 4. Another question I have is with gfdisplay. I went through the documentation, but did not find how to display 0318 bit 4 for example. I use gfdisplay already for a long time but never had to define an offset with a bit setting. Perhaps you have a hint for me. Many thanks Gilles

Hi Pete I tried out FSUIPC 4.07 today and found more stutters as before (4.067) on my remote pc. I use FSX on main computer with Projectmagenta on remote computers. Were there any changes to the wideserver module? Many thanks Gilles

I am using the 737-800

Hi I would like to use a Goflight GF45 module together with FSUIPC and gfdisplay to display the cabin altitude and climb rate. I also would like to use the knobs on the Goflight module to set the final cabin altitude and landing altitude. Many thanks Gilles

Hi Pete I am looking for an offset for the cabin altitude (and its format) in FSX. I was looking through the documentation, but could not find any information about a cabin altitude offset. Many thanks for helping Gilles

You mean by deleting the inside of the panel.cfg? Thanks Gilles

Thanks Pete for helping me I use the cirrus console from PFC. In the throttle quadrant tab I have no axis assigned. The only thing which is assigned in the PFC driver is the rudder, because I have a better throttle for a 737 I do not need anything else. I have to keep the console because my rudderpedal PFC hardware is not a usb version and I can connect it only through the console. If using (i know it is rather a PM question) Project magenta software which panel would you use? Perhaps the FSx overheadpanel functions are interfering with PMsystems? Many thanks Gilles

Hi Pete I have a big problem. Very often after about half an hour of flight with FSX and PMDG 737700, both engines shut down. I use FSUIPC4, PMsystems, PMBoeing, Cpflight hardware. I always thought the problem would come from PMsystems, but yesterday I shut down Pmsystems and the problem appeared as well. I checked if there were no axis wrongly assigned. I also use the pfc driver with pfc console but only for the rudder, the other axis are not assigned. A throttle is connected through fsbus. It seemed that after disconnecting the pfc hardawre console the problem had disppeared. But I will have to recheck. Are there any other such problems known?? Because I start to get desesperated.. Many thanks Gilles

First of all Merry Christmas !!!!! Many thanks for all the help during this year. I have one question concerning CPflight MCP and FSUIPC. With FSUIPC 4 and FSX, is there still an option for unchecking the box "Enable V/S correction". Or is this not needed anymore? Where do I find it? Many thanks Gilles

Thanks Pete I will try 4.063

Hi Pete I use FSUIPC 4.062 with FSX. I have assigned aileron an elevator axis in FSUIPC to send values directly to FSUIPC calibration. The problem is that the elevator and aileron axis move too easily and too sensitive even when using slope 15 for both and assigning a large space for neutral position. I also added to FS.cfg "Stick_Sensitivity_Mode=0" under controls. I tried in FSX axis assignment to delete elevator and aileron axis assignment, but then there are no values alo in FSUIPC calibration. So I have to keep the axis assignment in FSX to get FSUIPC calibration to work. I use in FSX calibration full sensitivity (100%) but no neutral zone. Many thanks for helping Gilles