Jump to content
The simFlight Network Forums

captgforce

Members
  • Posts

    26
  • Joined

  • Last visited

Profile Information

  • Gender
    Not Telling
  • Location
    United Kingdom

Recent Profile Visitors

1,040 profile views

captgforce's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. The above was posted by Vic in the "Tower 3D Pro" Topic.
  2. I think I might be in trouble if they release it then, as it's my wife's birthday, on that day too. We would not want to upset her indoors now....would we? (nudge nudge, wink wink, say no more)
  3. Hi Gabor I have T3D sp2a, KSAN sp1, RC KSAN and RT sp7 Regards
  4. Hi Gabor I was controlling at KSAN today, with your RC and RT SP7 installed. I noticed that a few problems are still present. Firstly, the SR22 is still not leaving the ground, even though T3D reports that it has taken off. It will continue along the runway, skip along the water and carry on into the trees on the west side of the airport. Secondly, there is a problem with both the A320 and the 737-800, which after landing, turn abruptly off the runway and come to a stop. They then have to be deleted as they will not obey any given instructions. I notice too that the 737-800 turns off the runway at the exit before the 737-700. Please see game log and screen shots below. This is of a Spirit A320 which was slowing down, then suddenly turned at the exit, still travelling quite fast. It then came to a sudden stop at the position you see here. After giving the commands "Taxi to Terminal" and "Continue Taxi" several times, with no response, the aircraft was deleted. This also happened with the 737-800 in the following screenshots. As noted, above, the 737-800 exits the runway before the 737-700. Should it not exit after the 700 and before the 900 as the above screenshot shows??? Best Regards
  5. I have found a similar problem at KPHL for all cargo aircraft. They will also cross Rwy 27L, without clearance, after being instructed to "Taxi to Ramp".
  6. I think the 787 textures came with RC for KJFK.
  7. Once you have issued the "Taxi to Terminal" command are they then holding short of 24L?
  8. Here are some problems regarding 07L. See screen shots. These are all T3D Sp2 with Real Traffic Sp2 and Real Colour with my own schedule. This is ANA6 stuck at 07L. Instruction to "Taxi to Terminal was given on exiting 07R. It then held at 07L but when given instruction to "Continue Taxi" it would not do so. After several attempts without success I had to delete it. This is JAL62, which is behind ANA6 in the previous screenshot. I let this aircraft get to the hold at 07L before giving it the taxi instructions, which it then carried out. This is of AC797, at 06R hold, which was given taxi instructions that it did not carry out after several attempts. Again the aircraft had to be deleted. This is of JAL62 spinning in circles at the TBIT Terminal. There were several other aircraft crossing or getting stuck at 06R or 07L. Here is the Game Log file: Game_Log_20161006_2106.log
  9. Log file at bottom of original post. Here is a collision on 07L when UAL506 had been given take-off clearance and GLA3033 had been instructed to "Taxi to Terminal" before it got to the hold, to cross 07L. GLA3033 failed to hold before it crossed 07L, hence the collision.
  10. I have now tried with the default Real Traffic schedule and the default T3D with the same result. See screenshots. This is VOI5926 crossing 06R after being given the instruction to "Taxi to Terminal" before reaching the holding point. It did not hold at the holding point as it should have. This is using RT default. Note the yellow taxi line on the ADIRS. This is AMX646 stuck at the hold 06R after being given the instructions to "Taxi to Terminal" and "Continue Taxi" using RT default. Note the lack of the yellow taxi line on the ADIRS. The A319, circled in blue, arrived at the gate, after an another aircraft had it left earlier. AMX646 has been assigned the gate in Red (see ADIRS above). Note the position of the jetway for the A319. This is of DEN24 crossing 06R after being given the instruction to "Taxi to Terminal" before reaching the holding point. It crossed without stopping at the hold. This is the default T3D. This is VAL2969 stuck at 06R holding point after being given clearance.
  11. I have not tried with the default but I will do.
  12. I found a couple of problems today at KLAX, when using the easterly runways (06L and 07R) for landing. Aircraft will cross runway 06R without permission if you instruct them to Taxi to terminal before they hold short of 06R. If they hold short of 06R then they will just stay there, even after instructing them to taxi to terminal or continue taxi. Please see screen shots. This is of FFT960 having crossed 06R without permission. This is of NKS504 which held short of 06R but then would not continue when instructed. I had to delete this aircraft. I have T3D SP2 with Real Traffic SP2 installed and using my own schedule. Here is the log file when I recreated a similar session with NKS504. game_20161004_2057.log
  13. Not on this occasion because the RJ was not active for departure. I did, however, get one a couple of days ago when a similar situation occurred but that time both a/c where active for departure.
  14. Hi I was controlling at PHL 14:00 taking screenshots of problems when I came across this possible collision alert (see screenshot).
  15. here are a few screenshots of gates that I have found without tugs.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.