These are the INput values? The OUTput should be from -16383 to + 16383. Are you not seeing that? Have you not calibrated, leaving a small "dead" zone at each extreme to ensure you can reach the minimum and maximum values?
It will if that is what it sees. When you assigned the axes in FSUIPC's Axis assignments, did you assign "direct to FSUIPC" or to the normal FS axis controls? Try assigning them direct, THEN calibrate in FSUIPC. It sounds as if you've not done this.
If you still have problems, please show me the [Axes] and [JoystickCalibration] sections from the FSUIPC4.INI file (in the FSX Modules folder).
Regards
Pete
Hi Pete!
Thanks for your quick response!
Here is the section of the ini file you have requested!
[Axes]
0=0X,256,D,1,0,0,0
1=0Y,256,D,2,0,0,0
2=0Z,256,D,4,0,0,0
3=0R,256,D,3,0,0,0
4=0U,256,D,6,0,0,0
5=0V,256,D,7,0,0,0
6=0S,256,D,5,0,0,0
7=0T,256,D,8,0,0,0
8=1X,256,D,1,0,0,0
9=1Y,256,D,2,0,0,0
10=2X,256,D,10,0,0,0
11=2Y,256,D,9,0,0,0
12=2Z,256,D,21,0,0,0
13=2R,256,D,17,0,0,0
14=2U,256,D,28,0,0,0
15=2V,256,D,18,0,0,0
16=2S,256,D,14,0,0,0
17=2T,256,D,13,0,0,0
18=17T,512,D,14,0,0,0
[JoystickCalibration]
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=66731
RudderTrimControl=66732
CowlFlaps1Control=66162
CowlFlaps2Control=66163
CowlFlaps3Control=66164
CowlFlaps4Control=66165
SteeringTillerControl=0
MaxSteerSpeed=60
Aileron=-16253,-2210,-650,15744
Elevator=-14823,-2210,-1690,16256
SlopeRudder=4
Throttle=-16384,16383
LeftBrake=-16384,16128
RightBrake=-16384,16383
Rudder=-16384,0,256,15488
PropPitch=-16384,16383
Mixture=-16384,16383
CowlFlaps1=1920,16256
CowlFlaps2=1920,16256
CowlFlaps3=1920,16256
CowlFlaps4=1920,16256
Throttle1=-15773,-512,512,15168
Throttle2=-16319,-512,512,14592
Mixture1=-16351,8192,8192,15200
Mixture2=-16287,8192,8192,16352
PropPitch1=-16351,0,512,16352
PropPitch2=-16351,0,512,16352
ElevatorTrim=-16223,-512,512,16320
Rudder Trim=-16255,-512,512,16383
What I find interesting that FSUIPC during the calibration routine "sees" the wholr throttle range i.e the value changes during the whole travel of the throttle input but in the simulater it reaches "Zero throttle when I still have 1/4 throttle travel left even after repeated calibration. It may be a FSX limitation though (or the pods I used??)
I use direct to FSUIPC mode.
I used 100 K pods when constructing the throttle. I used a reduction that uses about 250 degrees (Pretty much the full range of the pod)
I really apreciate your advise!
Kind regards
Alfred