sharonna

Thanks a lot for your help. I have tried it again, and again one axes is after reload not set as rudder anymore. Here is what ive edited: before editing: [Axes] 0=0Z,256,D,3,0,0,0 1=0U,256,D,3,0,0,0 after editing: [Axes] 0=0Z,256,D,3,0,0,0,*-0.5,+8192 1=0U,256,D,3,0,0,0,*0.5,-8191 regards martin EDIT: i got now the newwest fsuipc version, a voilla, i add the lines and it is set. Now under calibration my clutch goes from let out -16383 to pressed in 0 and the Accelerator from let out 16383 to pressed in 0. schouldn they be 0 wehen let out ? so the rudder is center I got it !! [Axes] 0=0Z,256,D,3,0,0,0,*0.5,+8192 1=0U,256,D,3,0,0,0,*-0.5,-8191 but how can i switch the direction ? at the moment when i press the clutch, left pedal the rudder goes right it works very smoothly, but when i set the rev option under calibration tab, only one pedal the is working okay now its working as i want !!! :D [Axes] 0=0Z,256,D,3,0,0,0,*-0.5,-8191 1=0U,256,D,3,0,0,0,*0.5,+8192 thank you so much for your help

Thanks for your answer, i see i have to learn much about fsuipc, so i will read the guides now. The purpose is to use the Clutch and the Accelerator for Rudder, cause they are going to press nearly at same strength, and they have more space between, cause in the middle is the brake... So this setup where, really better. As i wanted to test your suggestion now, i have noticed a strange thing: my pedals now have other values, the are now both in same value direction: Accelerator Pressed In: 16383 Let out: -16384 Clutch Pressed In: 16383 Let out: -16384 I dont get this, isnt this impossible ? i have no axis set in FS and sensitivity is set at maximum, and dead zone to minimum. So the userguide says. How would be the values for the ini file with this numbers, i have to add ? I am right that they also should be: ,*0.5,+8192 ,*0.5,-8191 I have tried it with the reload asignment button, ive set both axis to fsuipc direct as rudder, click ok, then edited the ini, opened fsuipc go to the axis tab pressed reload asignment, but then only on axis is still set as rudder, the second setting disappeard. Its too bad that i cant get it to workd this way, i think this is to complex for me. regards martin

Hi Peter I have readed the whole thread, and testet a lot, based on your description. But i dont get it to work, and i think i know where the problem is. First, let me explain the situation: I have the Logitech G25 Racing Wheel. This Wheel has 3 Pedals, Clutch, Brake, Accelerator. In the game controller settings it can be set as combined pedals or not. With combined Pedals Switched On, the Brake and Accelerator gets to one Axis and can be easily set in FS for the Rudder. The con with this config is, that the Brake goes very hard to push in, and the Accelerator easy, also this pedals are close together, so not very comftable. With combined Pedals Switched off, i have to set 2 Axis for the Rudder, same as here in the thread. But i dont get it to work, when i test it with a 2 Axis Gamepad your solution works fine, but not with my pedals. The Problem must be that in the case of the gamepad the sticks are going back to center, mean 0, but when i left the pedals out the value is at minimum or maximum, depends on what pedal is let out at last, and so the rudder stands complete left or right. My values are: Accelerator Pressed In: 16383 Let out: -16384 Clutch Pressed In: -16384 Let out: 16347 Have you an idea how i can make this to work ? I have tried it with these changes as you wrote: In what order to i have to config all ? Open FS, set the axis, click ok in fsuipc, change the ini files, go back to fs, open fsuipc and calibrate. Or must i close the fs at any point ? and to i need to calibrate it ? if so, how ? clutch left out = min, Accelerator pressed in = max, and what should i set as center ? My problem is also that anytime i open up fsuipc after the ini change, it deletes my changes from the ini file. Thanks in advance