Jump to content
The simFlight Network Forums

Morten

Members
  • Posts

    149
  • Joined

  • Last visited

Everything posted by Morten

  1. Yes I'm sure. All the sim hardware including throttles, yoke and pedals has been exactly the same all the time. All I have changed is new monitors and according to those I changed resolutions and the fullscreen setup. Also installed MS Office. And of course I can't tell whether any MS update could have had any influence here. /Morten
  2. However rather strange... Up till the latest P3Dv4.4 conditions were more tolerant without problems. Now conditions apparently are extremely sensitive in every sense - strictly, either FS control assignments for everything OR strictly assignments through FSUIPC, even including buttons! 😲 Amazing that all my joystick troubles during the last couple of months only comes down to this fact!! Cheers, Morten
  3. My dear Pete This was indeed your best advice of the year!!!!!!! EVERYTHING now works as expected, yoke, throttles and pedals! Wow! 😃
  4. I tried to mix tiller and rudder, assigning both to the pedals through "Send direct to FSUIPC Calibration". Not an option, at least not to my PMDG 777-200. The tiller mix reacted by turning the wheel all the way to each side. Not possible to go straight forward. I found the best solution till now, by assigning the axis rudder (no tiller mix) to my pedals and use "Send direct to FS as normal axis". This makes my front wheel turn fully perfect again as it use to couple a month ago! However my yoke, which is assigned trough "Send direct to FSUIPC Calibration", still go bananas if I choose to turn off the autopilot, as described above. No axis whatsoever, is no longer assigned inside P3D - Options - Axis Assignments. So what the heck is going on here?
  5. Okay Pete, got it! In fact my 'some what' common sense already told me before I even started this configuration!..hi, hi...life aint easy. The steering issue however, is left to solve - not for common sense to solve.. quite a drag...!!
  6. Moreover, according to this my previous statement and the following discussion, I've chosen as an experiment to completely keep my pedals out from FSUIPC. Which means that my pedals currently is calibrated within the P3D settings environment only, whereas my throutles and yoke is still calibrated inside the FSUIPC environment and send "direct to FSUIPC". With this combination I unfortunately still find my yoke going completely bananas and uncontrollable. It will happen mostly during an ILS approach, if I then choose to abort the autolanding and disconnect the autopilot in order to make a visual approach instead, then the yoke will turn all the way to the right and become totally out of control! The only way I can overcome this is by replugging the yoke into the USB slot and from then on it will be controllable again. All together, for some reason quite a mess here these days...?! Cheers, Morten
  7. Ok thanks, I'll get it a try. What is noticeable though, at least in my case, is that this lack of steering came about after updating from P3Dv.4.3 to v.4.4 - might be a random event, might not be... /Morten
  8. Hi Pete and John I guess, you're right and the problem is still present - probably just me getting more and more use to compensate the lack of turning by using cross throttling... I read the "FSLabs A320 Steering/Tiller debate" link which John provided me. However I'm afraid it got too nerdy for me and didn't really catch the conclusion, if any. Please bare over with me, I'm just a regular user and have no skills whatsoever into programming and special FSUIPC mods. So in simple terms, please; 1. Is there actually a way to mix the tiller facility with my (physical) pedal rudder axis assignment? 2. If so, would I actually benefit with such a mix in order to make my front wheel turning more efficient? (During turns on the taxiway I notice that the animated tiller on the PMDG 777-200 actually DO turn - whether this animation is actually a valid reflection of a tiller process taking place for real I can't tell) Cheers, Morten
  9. You really need beta folks to carry out what works and not works, before launching your appreciated updates.
  10. Fabio, this is no go, requiring customers to install all kind of stuff...if necessary it should be included in your install!
  11. No, Fabio! Both NET Framework already installed here on win 10. I have the exact same symptoms as "adribaradri" - your earlier version didn't have those crash issues! Back to the drawing board! /Morten
  12. Hi John Thanks for your profound suggestions... Now I totally erased axis for my pedals inside the FSUIPC.ini and instead established axes directly inside the P3Dv4 controls environment. So far steering is back to normal again. Cheers, Morten
  13. Hi Fabio Your default replay speed 1:1 is wrong - too fast!(Standard version) - Please look into the bug and correct! Cheers
  14. P3Dv4.4 FSUIPC 5.15 PMDG 777 Can't seem to configure my Saitek pedals correct through "send direct to FSUIPC Calibration" along with PMDG 777. Brakes and rudder works fine, but the front wheel works poorly, which means that I have to use my throttles violently as a compensation in order to make sharp turns. For my Saitek pedals ONLY I previously through the years used to send my Axis to "FS as normal axis" (rest of the "joysticks" direct to FSUIPC) which worked fine until FSUIPC/P3Dv4.3. From then on my other "joystick", my yoke, went totally bananas and out of control! No surprise here, as according to the manual, one is not supposed to mix "send direct to FSUIPC Calibration" and "FS as normal axis"...anyway this worked for a long time, until now when I don't seem to have no other choice than let all my axis on all my "joysticks" assign to "send direct to FSUIPC Calibration", which in practise wont work for my pedals! What is going wrong here? Would it perhaps help if I instead use "Send to FSUIPC Offset" ONLY for my pedals mixed with "send direct to FSUIPC Calibration" for the rest of the "joysticks"..? Cheers, Morten Attached files: log and ini. FSUIPC5.ini FSUIPC5.log
  15. It only seems to happen if "Record Audio during flight recording" is enabled - so uncheck this under Options!
  16. Couldn't find any simframework.xml in there. However I did find a simframeworkOption.xml - hope that this is what you mean. just PM'ed it to you. Morten
  17. Ohhhhhh for God sake, Fabio!!! Your very new, even STANDARD version, AGAIN suffer from random STOP just before landing!! Com on now!!
  18. Hi Fabio Would it be possible for you to make animations of cars on the roads? Also I see no AI aircraft at all during replay. Anyway, so wonderful that replay nows runs so smoothly and enjoyable - can't emphasize this enough, so glad that we're finally there!! 😂 (At least with the standard version - haven't yet had the guts to try out the new Exchanded P3D version..never mind) Cheers, Morten
  19. Hi Peter I'm afraid that your answer is not relevant in this case for several reasons: 1. I've had no issues whatsoever in terms of calibrating those exact same throttles prior to this 5.15 update. 1a. Also keep in mind that my update from 5.14 to 5.15 resulted in some screwed up throttles right away, which was the only reason for the need of a re-calibrating - That is, throttles screwed up, even though I did a copy/paste of the joystick values from the 5.14 ini file. 2. Your description of limits regarding to "less or equal to both Centres" makes no sense here, due to the fact that I always aime to make death zones plenty wide, in order to prevent sudden reverse mode when the intention was just put the throttles in neutral. 3. As mentioned before, for now with this 5.15 version I will only be able to EDIT the existing calibration which turns out fully successful - widespread death zones, or not. In other words, making a "virgin" reset before a new calibration is the only situation where hell is turned loose! So something seems to work out rather unexpected here with this 5.15 version. Cheers, Morten
  20. This is what I'm doing and have always done, Pete! But now the "virgin" install won't let me set new values - an error sound is ringing every time I'm trying to set the new values.
  21. Was about to finetune my "Separate throttles per engine" Joystick Calibration - for start hitted the Reset button per throttle as usually, then went on with setting values for Reverse/Max/Idle for all 4 throttles. Result: Respond from throttles where now totally wiped out in P3Dv4.4 /PMDG 777!! Tried again - this time without hitting the Reset buttons before calibrations. Then finished my calibrations as usual. Result: Succes! Have I missed something out? Perhaps forgotten something in the standard procedure? Or is there in fact a bug here..? Cheers
  22. No, not the case... Only difference between the "Options" in the two versions is that, in the standard FCR I have "Play recorded audio during Play mode" enabled - in the enhanced version I haven't enabled this mode.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.