Jump to content
The simFlight Network Forums

jan737

Members
  • Posts

    47
  • Joined

  • Last visited

About jan737

  • Birthday 01/01/1970

Contact Methods

  • Website URL
    http://

jan737's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. Hi Pete, Problem solved with the help of Thomas. Offset 0x6DB9 is correct. In FS you need to disable the Trim definition for the Buttons !!! Best regards Jan Geurtsen
  2. Hi Pete, I'm a bit confused how to setup FSUIPC 3.90. I would like assign two joystick buttons ( joy #0 1 Btn#) for Trim up. And ( joy #0 7 Btn#) for Trim down. Thomas provided 2 offsets for this 0x6DB9 Bit 0 for trim up and 0x6DB9 Bit 1 for trim down. Now I choose on the Buttons & Switches Tab and select "Offset byte select bits" Offset "0x6DB9" and in the parameter box "0" for trim up. Same for trim down. I'm not sure about "Offset byte select bits" because the trim function doesn't work. And I've selected "Manual trim" on TSR 737NG program. Hope you can help. Best regards Jan Geurtsen
  3. Hi Pete, I'm using the new program from Thomas Richter, Boeing 737NG software. For some of the new futures I need to write to offset 0x6DB5 (2 bytes long), wich is for the flaps handling in the new program. This offset will replace offset 0XDB0,but I'm not able to write to this new offset, also checked with FS interogate I'm using fs9 with the latest fsuipc 3.815. I'm using FSBUS CDK as softwarefor the hardware flaplever. Below I show you the lines I use: Standard I use this line , works correct. F, FFlapsCtrl, 0,0x0bdc, I32, 1,1,6,0,RW Now I change the offset for the new program F, FFlapsCtrl, 0,0x6db5, I16, 1,1,6,0,RW I don't see what went wrong over here, so I hope you can help me with this. Best regards Jan Geurtsen
  4. Hi Pete I have a problem with the 737 PM GC EICAS where the flaps gauge or indicator not responding anymore when the flaps are set. Moving the flaplever, sets the flaps on the aircraft in the right position, but the PM software doesn't notice that and the flapsetting stays at 0. Revert back to FSUIPC 3.80 solves the problem. Best regards Jan Geurtsen
  5. Hi Pete Thanks for the quick answer. Setting the hour was only for example. I want to set the time by hardware, such as fsbus or FDT. So i want access direct to the offsets and not via the button page of FSUIPC. Best regards Jan Geurtsen
  6. Hi Pete I'm thinking about to make a Boeing style clock for my sim. Is it possible to set the time for i.e. to offset 0x0238 with a pushbutton? If this is possible it makes planning my clock much easier. Best regards Jan Geurtsen
  7. Hi I have a question about key combinations and Fsuipc. I'm using the keyboard of my FS computer to control my KVM switch. The key combination is Alt-Ctrl-Shift 1 [Enter]. The number 1 can vary from 1 to 4 for wich computer I select. Now I like to make 4 buttons who send the above key combination to the Kvm switch so I don't need the keyboard anymore. Is this possible? Best regards Jan Geurtsen
  8. Hi Pete Clear now. I think the best way is to by a USB axis card from opencockpits. Thanks again Best regards Jan Geurtsen.
  9. Hi Pete, I'm not sure that I understand you right. So, when I use offset 0BBA in fsbus and use a potmeter for the axis, I can(must) calibrate the axis in fsuipc. Is that what you are saying? Best regards Jan Geurtsen
  10. Hi Pete, I like to make my own steering tiller by using a potmeter. I use fsbus as interface and need a offset for the tiller. I couldn't find an offset in the doc's. Hope you can help me. Best regards Jan Geurtsen
  11. Hi I'm building a analog brake pressure gauge for my 737NG. Is there a offset availeble for the brake pressure? Best regards Jan Geurtsen
  12. Pete, Thank you,I'll test it later this (week)end. Best regards Jan Geurtsen.
  13. Hi Pete In the aircraft.cfg there are 2 adf's enabled. The following I found out: ADF1(fs2004) freq. = ADF L freq. PM CDU. ADF2(fs2004 )freq.(x02D4) is not ADF R freq. PM CDU. When I tune the ADF R (cdu) this tune to the required ADF freq. in the ND. This doesn't match with the FS ADF freq. displayd in the ADF2 radio of the panel. So, this sounds strange to me, why doesn't match the ADF2 freq. to the ADF R ??????? Will check with fs-interrogate later to find the offset of the ADF R cdu. Best regards Jan Geurtsen
  14. Hi Pete I want to set the ADF R freq. (CDU) via fsbus hardware. I tried all the offsets listed in the FSUIPC offset list. But only the ADF L is changing if I use my hardware to change the ADF freq.When I use the CDU key's I can change the ADF R FReq and this is also displayd on the captains ND. Do you have an idea wich offset to use to change the ADF R freq? I'm using fs2004. Ask this question before in the PM forum but there was no solution. Best regards Jan Geurtsen
  15. Hi Pete, For the 737NG pedestal I need a offset to swap the ADF 1 and ADF 1 stby. I take look at the manuals but there are alone offsets on address 3123 for the comm and nav's. Is it possible to add them? I'm using the full PM 737 and pm systems software. Best regards Jan Geurtsen
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.