
TorranceR1
Members-
Content Count
9 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout TorranceR1
-
Rank
Newbie
Profile Information
-
Gender
Male
-
Location
United Kingdom
-
Saitek Throttle Setup
TorranceR1 replied to TorranceR1's topic in FSUIPC Support Pete Dowson Modules
Hi Pete. I'll reinstall the drivers for my quadrant and if the problem still exists. If it still exists then I will do what you said and take a look at their support forums. Thanks, Robbie -
I have recently been trying to setup my Saitek Throttle and seem to be having some problems. I have Assigned to axis' on my throttle to a throttle each aka. Axis Y for Throttle 1 and Axis Z for Throttle 2. I assigned both in the Axis assignment section of FSUIPC and then pressed 'Set' for both Throttle 1 and 2 in the Calibration section but when I went into the VC I had a problem. I tried moving both at the same time and the first thing I noticed was that Throttle 1 jumped straight to about 50% even though I only pushed it forward slightly on my Saitek Throttle. Throttle number 2 seemed fine,
-
Second Throttle Not Being Picked Up?
TorranceR1 replied to TorranceR1's topic in FSUIPC Support Pete Dowson Modules
Finally fixed the problem. Just had to update the drivers which I probably should have done earlier! Thanks for the help Pete -
Second Throttle Not Being Picked Up?
TorranceR1 replied to TorranceR1's topic in FSUIPC Support Pete Dowson Modules
Hi again. I actually already have the JoyID's software and I tried switching about the different ID's but still no luck. Robbie -
Second Throttle Not Being Picked Up?
TorranceR1 replied to TorranceR1's topic in FSUIPC Support Pete Dowson Modules
Hi Pete. Yes I have calibrated them through windows and everything seems to be fine. I also tried assigning them through the FSX controls section and they were also picked up although having it assigned through FSX controls isn't ideal for me as I am on Windows 8 and if I do this I will be faced with many problems! Thanks, Robbie -
Second Throttle Not Being Picked Up?
TorranceR1 posted a topic in FSUIPC Support Pete Dowson Modules
Hi all. I haev just recently purchased a Saitek Throttle Quadrant to go with the one I already own that came with my yoke however I am having problems with setting it up in FSUIPC. When I go into the 'Axis Assignment' page in FSUIPC, click 'Rescan' and move any of the 3 axis' on my NEW throttle they aren't picked up! When I move my already owned throttle's axis' they are picked up...? I hope to hear from someone soon! Any help will be appreciated. Thanks, Robbie -
Rudder and Brake Axis not Recognized?
TorranceR1 replied to TorranceR1's topic in FSUIPC Support Pete Dowson Modules
Thank you very much Pete. That has worked. Now I can get back to flying as normal! Again, thank you! Robbie -
Hi. I have been using FSUIPC for about a month now and have been very pleased with it. Although I have recently ran into a problem. I now have no control over my rudder and brake axis. I use saitek rudder pedals and therefore have a rudder and brake axis in the one controller. I tried to assign the rudder and brake axis through the Axis Assignment section of FSUIPC but every time I move either the rudder or brakes it is not picked up inside FSUIPC. I tried looking at saiteks own control panel for the pedals and everything seemed fine their, all axis working and moving in the calibration. I als
-
Hi, recently I have bought FSUIPC and really enjoyed it with the massive variety of things to do! Up until recently where I have run into a problem with assigning the throttle. For some reason the throttle axis reset itself so I tried to go into FSUIPC and reassign it, but that didn't work. When I go into the Axis Assignment tab, then move the axis on my throttle that I want to use for the throttle, I have a problem. When my throttle lever is at 0% or idle it shows -16384 and when it as at 100% is shows 16384. But anything in between 0% and 100% doesn't seem to work. So from 0% all the way up