Jump to content
The simFlight Network Forums

Search the Community

Showing results for tags 'support'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Product Support Forums
    • FSUIPC Support Pete Dowson Modules
    • MyTraffic Support Forum
    • FeelThere Support Forums
    • FS Commander Support Forum
    • Flying W Simulation
    • AConstable Traffic Sounds Support Forum
    • Fabio Merlo Products Support Forum
    • Elite-Air Studio Support Forum
    • Nikola Jovanovic Support Forum
    • Intrasystems Support Forum
    • FScene Support Forum
    • Taburet & DanVFR Support Forum
    • Environ Scenery
  • simFlight DE
  • simRussia
  • FSUIPC Client DLL for .NET


  • Community Calendar


There are no results to display.

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 10 results

  1. nixdevelopment

    TOPER Web - Support

    NOTE: Please mention the device you are using to access TOPER Web Please post your queries here:
  2. Hello Pete would the offset &H308 #11 value (FSW), be soon supported in FSUIPC5 ? i know the FSW SDK is not almost completed and documented, but in any case, if you're already ahead for this insight into Best Regards Gilles
  3. Hi, What is the best means for end users to report bugs for Tower!2011:SE? I have recently purchased the game and there are a LOT of issues I am coming across that need to be fixed in order for me to recommend this game. The website has no place for support apart from this forum. Please advise. Regards, eikcam.
  4. OS: Windows 8 (I run airfield editor as an admin) Airfield editor starts fine until I attempt to insert the .TGA for the no shadow top down view. I named the file "San_Diego_Airport_final_noshadow.tga" After I select the file, the editor freezes then crashes shortly after. The first couple times I tried to insert the file nothing would happen but the editor would remain open and functional. I can attach the .TGA as a .PNG below if necessary. Thanks for the help
  5. Hi, I brought this tool last night and i have downloaded and installed it, but i see all field strange and this make impossible to use the software. I have the lastest version and i'm using Windows 7 with .NET framework 4.0 Here some screen: The issue: As it should be, according with the manual. Thanks in advance for any help.
  6. Mike1997

    Tower! 2011 Bundle

    Dear Feelthere-Team! I just bought the bundle for Tower! 2011 which contains KRDU, KOHL, KORD, KDFW and KSAN. I later noticed that i had not revieved a downloadlink for KSAN. Thanks in advance! Michael
  7. I am having a strange problems since updating to latest version of FSUIPC with the elevator trim on all my aircraft. As soon as I start my engines during pushback my elevator trim begins erratically moving up and down until I start to taxi and the plane reaches a few knots ground speed at which point the elevator trim corrects itself. Thou it is not a serious bug it was bothering me enough to uninstall FSX and reinstall my 60+ gigs of addons which unfortunately has not fixed anything. I have tried running FSX without my flight yoke. I've updated all addons and drivers. I've spent a few hours browsing support forums and still have not found a solution to my problem. Is there a way to disable auto trim when auto pilot is disconnected? Any suggestions would be greatly appreciated.
  8. Please post your queries here
  9. Hi, I recently downloaded the BlackBox widebody prologue, and while setting up the load manager for the it asked for FSUIPC to install, which it did. I then made the decision to go and buy the full license for it. I reinstall FSUIPC4 off of the website. After which, when I went to turn on FSX:SE it asked me to verify to run the FSUIPC4_loader.DLL and as soon as I press "run" FSX just closes on the intro screen and my EZDOK gives the message: "FSX Process not found. FSX_Handles: 0" Usually when I got this error, reinstalling FSUPIC (Free version) just did the trick, but reinstalling doesn't seem to do it this time. Any help would be great, Thank you much!
  10. To fix “Database file missing. Please re-install” message which occurs with original release 1.00.0 please visit the updates section and follow the instructions.

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.