Jump to content
The simFlight Network Forums

Tower3D Pro CAT of different aircraft


Recommended Posts

Related to this, if anyone can explain to me the flight strips I would be grateful. I understand some basic information on them, but cannot decipher where the Category I, II or III is designated as Chazsi and Sky King asked above.

Thanks!

Link to post
Share on other sites

RickyJ:

I understand what the categories are- what I would like to know is can you look at a flight's strip in Tower!3D and know what the category of a given aircraft is? Not trying to be a jerk here, I just want to know what information is relayed on the strip. Some of it is dead obvious, the rest? - not so much.

Note: I looked at the Avwriter thread you quoted and saw your breakdown on one flight, thanks. So, are all (M)edium/Cat II flights noted as XXXM and all (H)eavy/Cat III flights as XXXH in the game?

Thanks.

Edited by Pdubya
clarification
Link to post
Share on other sites

From a sim perspective, I really haven't seen where the category type makes a difference. The manual talks a lot about separation on departures. However, you can have a Cessna take off immediately after an A380 has successfully departed without applying any "required" separation and you won't get dinged for it.

 

Regarding the strips, they look similar to the strips in Tower!2011. Below is from the 2011 manual:

Deciphering an ARRIVAL slip -
Column 1:
• Line one - aircraft call sign and flight number (see Airline identification codes)
• Line two – equipment type (Aircraft identification codes ). Heavy aircraft will have their equipment type followed by /H (See The Theory Behind Air Traffic Control for discussion on aircraft separation rules.)
• Line three – an arbitrary number assigned by the program that generates the strips
Column 2:
• Line 1 – a computer generated arbitrary number
• Line 2 – expected arrival time reported in UTC.
• Line 3 – flight level of aircraft when transferred to you by arrival control
Column 3:
• Line 1– destination airport
• Line 2 – departure airport
Column 4:
• When the aircraft has been cleared to land a check mark will be shown in this datafield..
Column 5:
• Lines 1 up to 3 – assigned runway. Will have a cross through when new runway is assigned.

Deciphering a DEPARTURE slip -
Column 1:
• Line 1 – aircraft call sign (see Airline identification codes)
• Line 2 – equipment type (see Aircraft Identification Codes for more information. Heavy aircraft will have their equipment type followed by /H (See The Theory Behind
Air Traffic Control for discussion on aircraft separation rules.)
• Line 3 – An arbitrary number assigned by the program that generates the strips
Column 2:
• Line 1 – a computer generated arbitrary number
• Line 2 – time of departure, reported as UTC
• Line 3 – flight level of aircraft when transferred to you by arrival control
Column 3:
• Line 1 – departure airport
• Line 2 – destination airport
Column 4:
• Tower will display controller notes under these circumstances -
✔ For local flights the number of go-arounds, low approaches and touch and goes the plane will conduct.
✔ Display the assigned runway intersection for takeoff (see Ground commands, AT command).
✔ When you clear an aircraft for takeoff a check mark will be shown.
Column 5:
• Lines 1 up to 3 – assigned runway. Will have a cross through when new runway is
assigned.

Aircraft Identification Codes

CODE COMMON_AIRCRAFT NAME      SIZE BODY_DESIGNATION
JTO     Wide-body default jet                    H      WIDE BODY JET
JT1      Narrow-body default jet                 L      NARROW BODY JET
RJ1     Regional jet                                   S      REGIONAL JET
TRP    Turboprop                                      S     TURBOPROP
PRP    Propeller airplane                          S      PROP

  • Upvote 1
Link to post
Share on other sites
1 hour ago, Pdubya said:

RickyJ:

can you look at a flight's strip in Tower!3D and know what the category of a given aircraft is?

Yes, when I see the plane is a 73W, I know that it is a 737-700, its' maximum takeoff weight is 154.500 lbs which makes it a category 2 plane. But I do not have to look at its' designation since I have Nyerges Real Traffic and Real Color I can tell what type of plane it is just by looking at it.

Good job Nyerges,
RickyJ

  • Upvote 1
Link to post
Share on other sites

Thanks to you both, that helps a lot. Perhaps later this year we are due for a manual update. It would help with reducing newb questions. I found the current one lacking, lots of repetitive paragraphs and basic information but no specifics to answer your questions. I'll leave it at that as I know FT are a small company and rather busy with stuff.

Oh, I also was wondering if the 2011 manual is still available to access or download.

Thanks again.

Link to post
Share on other sites
  • 3 months later...

Question about line 2 column 2. How is that the expected arrival time? Maybe it's different depending on the airport. At KLAS starting at 0800, the number is 5181 for every arriving aircraft. This number isn't a time. Can @FeelThere or anyone else clarify what that number is supposed to be?

Rameus

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.