Jump to content
The simFlight Network Forums

EGKK Bugs


andredragt
 Share

Recommended Posts

AFTER SUGGESTION: Rewritten just a few posts down.

 

Took me a while to find some bugs 😃

Bug 1:

If I have a plane taxiing eastwards on Kilo, it first goes north before turning south on Papa (turnoff not connected?)

Bug 2:

Planes going south on Papa with information 26R@A by P AS are holding short of the crossing AS/B instead of continuing to 26R

Same bug probably, planes with info 26R@B by N B are doing the same, with added problem that if you give those a Continue taxi command, they will Line up on 26R

 Bug 3:

Terminal S1 only seems to have 1 active gate (the one in line with Taxiway Z)

Link to comment
Share on other sites

Bug Report now with output log.....also..found Bug 4

This report is generated while using Nyerges RC/RT

Bug report

Extra Remarks are underlined

 

Bug 1:

If I have a plane taxiing eastwards on Kilo, it first goes north before turning south on Papa (turnoff not connected?)

I noticed that this is only if the plane starts on Kilo

EGGK-northPapa.png.f6c5044e2e9c21fbb5e6ffb12961ac03.png

Bug 2:

Planes going south on Papa with information 26R@A by P AS are holding short of the crossing AS/B instead of continuing to 26R

Same bug probably, planes with info 26R@B by N B are doing the same, with added problem that if you give those a Continue taxi command, they will Line up on 26R

so, misplaced Runway-Treshold?

 

EGGK_PapaShort.thumb.png.28242747d8e5febf96d6ccd30b114839.png

EGGK_BravoShort.thumb.png.4ae6b9c5cb0c577d2791532059e9af3c.png

 

 Bug 3:

Terminal S1 only seems to have 1 active gate (the one in line with Taxiway Z)

To make sure I was right, I made sure EZY only had Terminal S1 as option... the terminal should be completely full...

 

EGGK_EmptyT1.thumb.png.5b6273a369386561742dcea2572efed7.png

 

Bug 4:

See that Virgin Plane above in the ADIRS.. yeah, I accidentaly gave it pushback to 26L.... so completely stuck now, apparantly you can't use that one (08L does work)

 

Bug 5:

Terminal 3 does not accept Heavy Planes, see KTPA & KMCO Coming Into Gatwick

 

Also a general question/remark. I noticed in ATC-Joes schedule that some airlines didn't had a terminal, but did spawn. So for fun I removed all airlines from the terminal file... they are now all over the place

Link to comment
Share on other sites

  • 2 weeks later...
On 3/3/2019 at 6:41 AM, andredragt said:

Took me a while to find some bugs 😃

Bug 1:

If I have a plane taxiing eastwards on Kilo, it first goes north before turning south on Papa (turnoff not connected?)

Bug 2:

Planes going south on Papa with information 26R@A by P AS are holding short of the crossing AS/B instead of continuing to 26R

Same bug probably, planes with info 26R@B by N B are doing the same, with added problem that if you give those a Continue taxi command, they will Line up on 26R

 Bug 3:

Terminal S1 only seems to have 1 active gate (the one in line with Taxiway Z)

Bug 1. After pushback, if you just give a continue taxi to RWY 26L it's works fine, but if you issue specific taxiways to use to get to 26L, then it acts as you described!

Bug 2. I have also seen this at this airport, I think it may be something to do with the holding points for Bravo, maybe.

Bug 3. Also seen this too, using Real Traffic

*

One further point to add, at the real airport traffic heading for 26L do not routinely use taxiway Juliet east of November, due to 777's and 747's chopping tails off parked aircraft. They either use Zulu or AN/AS to get there, but T3D's automatic routing is down Juliet for aircraft coming from the West side of November.

Edited by scoobflight
Edit: comments removed as inappropriate for this forum. -Mods.
Link to comment
Share on other sites

  • 4 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.