mabainca

And finally is not necesary to add my log due work perfect after calibrate again the throttle from beginning. only i have desactivated the specific aircraft tick when i use fsuipc. Dont ask me what has it been the solution. i dont know..:-). Thank Pete for your full cooperation Regards Manuel

Using 737 default. Checked aircraft.cfg. 0.25 - 25%. My throttle has the next setup. Engine 1 from -6072 to 2656 And Engine 2 from -4754 till 3872. I use the offset x088C for engine 1 and 0924 for Eng 2 And parameter: -4095 following your advice And nothing. Throttle properly calibrated. No jitter to interference And has a good idle position. I enable Fsuipc console And both reversers buttons work fine but dont activate the reversers. Ive checked diferents parameters valúes And axis configuration And nothing. Thank pete but at the moment without results. Mabainca

Well copy Pete I Will do this And i Will answers you with my results. Many thank Mabainca

Good morning Pete I am with the JETMAX Throttle configuration now and i try to setup the engine reversers. JETMAX use buttons to do this. Following his manual: http://www.flightdecksolutions.com/pcupload/JetMaxTQv1.3.pdf (Page 21) Engine Reversers Engine reversers are switches in the JetMax throttle lever, use the following offsets: Offset Word Set Eng 1 Offset x088C Parameter -5800 End 2 Offset x0924 Parameter- 5800 Use Offset Word Set and the same offsets but use 0 as a parameter for returning to IDLE. I use this offsets following the manual indication and pics inside manual but doesnt work. I use FSX, IFLY 737 and IFLYTOFSUIPCS (the offset is not inside IflytoFsuipc manual to do this). Have last FSUIPC version new offsets? any idea? Thank for advance Mabainca

Sorry Pete for my delay to answer your post. Finally I have solved the problem. The problem was that i installed FSUIPC before VRINSIGHT software. I reinstalled FSUIPC and work fine now. Many thank!!! Mabainca

Good afternoon Peter I have just to install the last Fsuipc versión And doesnt work with my vrinsight overhead. I have had to downgrade to 4.7 And now work fine. The problem is that the vrinsight software doesnt find the fsuipc installed. Any idea?? Regards Mabainca

Many many thank I will contact with IFLY2FSUIPC and IFLY 737 developer again. I hope to solve this small problem soon, in that case i will updated this post with the solution. Best regards Manuel

Good morning Pete Many thank for your fast answer. Sorry for my second exactly post. It was involuntary. I will be briefly: I want to connect my flightillusion gauge with my IFLY 737 addon. (IFLY2FSUIPC gets data from IFLY and puts it into FSUIPC). The problem is: My gauge work, but not show me the identical value as IFLY has in the main panel when the brake pressure decrease. When i push the button (brake "." into flight simulator) i check that the needle gauge decrease but not follow the same behaviour, after release the button increase suddenly again. No mantain the position as a flaps gauge for example. I dont know if this is normal or maybe i need another way to connect it. (using language to program it). Thank again and sorry Manuel

Good afternoon I've a question and i dont know if this is the appropiate forum. I have tried contact with Flightillusion and IFLY support but not answer at the moment. I've FS9 + IFLY 737 (updated last service pack) + FSUIPC (Last version) + Ifly2FSUIPC + GSA-28 (Brake pressure) with flightillusion software. I have offset and SDK but I dont get make progress and doesnt work. Does FSUIPC read gauge value? Must i setup or insert the offset inside FSUIPC? Maybe is not compatible with this aircraft. any idea? Many thank for advance Manuel