sacramento

Hi Pete: Yes i respect your time, and i know, you must have a lot off thinks to do that answear questions, i know that, and if you see i have in this all forum 24 posts, that's because, before i post a post, i search for the subject i would like, and believe me it's very hard for me bother persons, but when i don't have more resources i need to post... Ok let's leave this subject and let me test again with the offset you had send me.... Thanks and accept my apologies

HI: I do not know why people get upset by asking questions that have nothing to do with knowing more than the other or do not trust what the documents say, but doubts that are simply questions, and we try try but not we can't and we need help! Resuming will doubt, I think that still did not understand my question then to be jumping to conclusions, but is ready to again! Thanks anyway

Hi Pete: Thanks for the information... Just yet the offset 0BC0, that's only that i would like to know it's the format to enter the values! Because you just teel in the offset the range -16383 and +16383, but the way to enter the values is: *360/65536? Thanks

Hi Pete: Thanks for your reply... The potentiometer are connected to an electronic board, and he can not see as an AXIS, that's because i thought in use the 0BC0 offset... I could try your sugestion, that sounds more easy for me, via programming, but for user, required a little more knowledge to calibrate etc etc...already now, have you a offset that could i setup the trottle of PM, via axis assignement's on FSUIPC? Anyway, just for my knowlodge, can you tell me, in case of Offset 0BC0, the values that we must enter? Thanks

Hi: I would like to use the Offset 0BC0 that is for use to elevator Trim Control....My potentiometer give me values from 0530 to 3ad0 Hexadecimal.... Question: I need to convert first the hexadecimal value for decimal and then multiply for 65532, and send? If possible, please, tell me the way to do this ok? THanks Manuel Sacramento

Hi: I had see the list off FSUIPC offset and i'm not sure the best offset to work with squawk in mode charlie and STDY mode. If anyone could give a little help I appreciate. Thanks Manuel Sacramento

Yes completely remove it! Windows XP profissional...version 2002 with SP2 Other things Added - a Module COM of go flight

Hi Pete: I had made the tests you had required and: Download maked and the FSUIPC are used in Modules folder...Problem remain I always running FS in Windowed mode... . Addons - Project Magenta IVAP I have only the defaults aircrafts and more one to PM... The FS as been installed again to try this tips! I had try with others defaults flights and the problem remain Ok...before I send you the .DLLs I have in the modules folder i had try the FSUIPC 3.53 and the FS work very well...this mean something to you? If I change to version 3.715,the FS don't load...strange no? Thanks

Hi Pete: Ok...thanks for the tips...This tonight I will make the tests you had recommend. Then I will report to you the results Manuel Sacramento

Hi Pete: Thanks for your reply... When I say don't answear,the FS don't enter...the FS don't enter to the main menu...I make CTRL+ALT+DEL in my PC and the status of FS is No answear. The version is the last version 3.71 Thanks

Hi Pete: A strange problem are hapen in my PC...If a remove the FSUIPC.dll from the modules folder,the FS2004 start correctly... If I put FSUIPC.dll in modules folder the FS2004 don't answear,and consequently can not enter! My firewall is disable in antivirus panda and Windows XP! Any resolution for this? Thanks Manuel Sacramento

Sory Pete...I had Find...is installed in the modules folder of FSX.... The problems is resolved Thanks

Hi Pete: I can not find: Advanced User's guide for FSUIPC4 I just have User guide for FSUIPC4 and I don't find any detail about: Programs: facilities to load and run additional programs Thanks

Hi Pete: In FS2004 i use this: [user] run1=d:\iocards\sioc.exe run2=d:\pmsounds\pmsounds.exe close1=yes close2=yes I had try in FSX in section [Wideserver],but notthing happens! Can you tell me here I can put this in FSX? Thanks

roger that sir thanks

Ok guys...I had find the way to this this...but Pete(if you read this topic)...the variable PM AB THR REV IDLLE have a problem...the slider don't stop when this offset is setting! Thanks

Hi to all: In this time i finish my trottle for Airbus,to my home cokpit and I need to know if it's possible to assign via FSUIPC the gates(REV,IDLLE,CLB,FLX,TO/GA),and the two levers(engines) separattly....the software is project magenta. I have board who simulate the normal joystick,the diference is just the two engines...this board separe the engines.... Thanks

Hi Pete: After a few tests in VATSIM a had concluded the problem it was with IVAP. VATSIM with your FSINN work very well and I don't Have problems with pressure. In this moment I already had post the problem to the IVAP programmers and I had a reply to this problem...In fact they assume,IVAP have a few problems with Wheather,and they want to know a few more thinks for help in this problem. Thanks

Yes me too...When I fly Offline everything work fine...no problems Yes I had try with this option checkek in FSUIPC,and the problem remains! Not yet...I will go enable weather logging to see what happen! Maybe the major part off people don't fly with PM online and with IVAP...I had say to Enrico try,but...I don't know if he had try!!

A IVAP support??I don't know if they resolve the problem,because you can fly all the aircrafts in FS,and you don't have this problem,with IVAP,but if you fly with PM,the problem appears... The Problem is from PM or FSUIPC or IVAP???Who's Know?? If you have PM,please try and you see what I say! I can not find where is the problem!

Hi Pete: No... don't work...I had set these option and I continue with the same problem!I had make a few tests and this happens in a higher FL's like 350/370/390! This only happens with IVAP...iif you turn off IVAP and call the weather trought FS,via net,everything work fine! Strange no?

Hi to all: I had post a post in PM forum about this situation... Here is the post: Enrico say: Can anyone tell the way to set FSUIPC for this not happen? Thanks

Hi to all: I want to know if was good for project magenta and wideFS be a swicht with 1GB/lan and off couse in all computers clients with network cards too! We take advantage with this speed or not??? Thanks

Hi to all: I need a help here because I try to put allowshutdown=yes and all .ini files computers I have Project Magenta but in MCDU I can not shut down the otthers computers,just MCDU. Can anybody tell the assignements in the .ini file off wide server,or otthers instructions?I don't know why the MCDU don't shut down all computers!! Thanks