Patten

October 1, 2013

thank you, Pete, your help is much appreciated.

I'll give it a try asap and let you know the result.

greets,

pat

September 30, 2013

Thank you Pete for your fast reply.

What I want is 1 module at the time made active:= 1 freq in use and 1 in standby for the active module and the other module set in non-active at the same time (= 1 freq to become in use, when that module becomes active + 1 freq standby).

The purpose is for ex.: presetting ATIS + Delivery in COM1 and Ground + TWR in COM2 ; would be handy with ATC ; but as said RadarContact does only use COM1, so having 2 Comm's is useless in that case.

If you say that this can be achieved with LUA, then I'll have to plunge into the manual, because I never had to use it before.(the configs via your FSUIPC have been very usefull indeed for all I needed )

thanks again.

September 30, 2013

Hi Pete,

as I couldn't find an answer on the radar contact forum, I put my hope on you.

my (not so big) problem : I have 2 cpflight comm modules and would like to use and switch both with RC.The problem is that RadarContact only uses COM 1 .

So in order to use COM2 , the program has to be "fooled" in thinking that COM 2 is COM 1 , when switched.

Do you think this is possible ?

Thanks, greetings,

Pat

my config : FSUIPC reg, WIN7-64, FS9.1 and IFLY738.

April 8, 2013

Hi,

You can direct the RC output from the network PC using the line-out, and into the FS PC using the line-in: I have done this using a male-to-male audio cable, and know it works.

See the thread at: http://forum.avsim.n...worked-machine/ where this is discussed.

Regards,

Chakko.

works indeed ! txs a lot .

Pat

April 5, 2013

I can't think of any really good reason for doing it, otherwise!

Regards

Pete

what about a wife who wants to keep things quiet ? (i.e no FS noise !) :???:

April 5, 2013

Hi,

You can direct the RC output from the network PC using the line-out, and into the FS PC using the line-in: I have done this using a male-to-male audio cable, and know it works.

See the thread at: http://forum.avsim.n...worked-machine/ where this is discussed.

Regards,

Chakko.

Thanks a lot for this advice ! I'll try it asap.

greets,

Patten

April 5, 2013

Hi Pete,

Just installed AS6.5 and RadarContact4 networking via WideFs on my old laptop.

It's working perfectly !

Just one question: is there a possibility to have the RC ATC and the cockpit sounds together on my one headset,as before, when FS9 and RC4 were on the same PC?

Thanks ,

Patten

April 15, 2011

Hi Pete,

sorry for late respons.When reinstalling the driver from cpflight, other strange things happened.So I went for the FSLABS driver (somewhat expensive), and that seems to work perfectly.So won't spend more of your time, but would like to thank you for your help.

regards,

patrick

April 8, 2011

You can paste the contents of the Log in a message here. It would be neater if you enlosed it, not as a Quote (like above) but as "code" -- the button looking like <> above.

I don't know how you've assigned the functions, if you have, or if they are supposed to emanate directly from the cpFlight driver. So we might need to proceed in steps. In the first instance, only put a check mark against "Events". Don't touch anything else on that tab at all. Not yet. Keep the session as short as possible, only enough to reproduce your problem. Then close FS. Paste up the whole log, and describe exactlyt what you did.

Regards

Pete

hi Pete,

I didn't assign anything from the MCP ; only Yoke and rudderpedals are assigned and calibrated via your module.

I made an eventlog from starting up the MCP untill set.(nothing touched)

I made also a second eventlog when changing spd and switching to VC, but as it was a too big log it couldn't be posted here.

Nevertheless when comparing the 2 logs, they seem quite identical, so I suppose this won't get us any further.

hereby the 1 log(shortened because even this one is too long), hoping to hear from you for further investigation,

regards,patrick

********* FSUIPC, Version 3.989z by Pete Dowson *********

Running inside FS2004 (FS9.1 CONTROLS.DLL, FS9.1 WEATHER.DLL)

User Name="patrick dochy"

User Addr="patrick.dochy@skynet.be"

FSUIPC Key is provided

WIDEFS not user registered, or expired

[Continuation log requested by user]

Module base=61000000

WeatherReadInterval=4

LogOptions=00000001

247714 System time = 08/04/2011 10:28:29, FS2004 time = 14:39:17 (13:39Z)

248119 *** EVENT: Cntrl= 66069 (0x00010215), Param= 1 (0x00000001) YAW_DAMPER_ON

248119 *** EVENT: Cntrl= 65961 (0x000101a9), Param= 0 (0x00000000) FUEL_SELECTOR_CENTER

248119 *** EVENT: Cntrl= 66391 (0x00010357), Param= 0 (0x00000000) TOGGLE_TAIL_HOOK_HANDLE

248119 *** EVENT: Cntrl= 66330 (0x0001031a), Param= 0 (0x00000000) DEC_COWL_FLAPS1

248119 *** EVENT: Cntrl= 66337 (0x00010321), Param= 0 (0x00000000) TOGGLE_STRUCTURAL_DEICE

248119 *** EVENT: Cntrl= 66069 (0x00010215), Param= 1 (0x00000001) YAW_DAMPER_ON

248119 *** EVENT: Cntrl= 65961 (0x000101a9), Param= 0 (0x00000000) FUEL_SELECTOR_CENTER

248119 *** EVENT: Cntrl= 66391 (0x00010357), Param= 0 (0x00000000) TOGGLE_TAIL_HOOK_HANDLE

248119 *** EVENT: Cntrl= 66330 (0x0001031a), Param= 0 (0x00000000) DEC_COWL_FLAPS1

248119 *** EVENT: Cntrl= 66337 (0x00010321), Param= 0 (0x00000000) TOGGLE_STRUCTURAL_DEICE

248135 *** EVENT: Cntrl= 66069 (0x00010215), Param= 1 (0x00000001) YAW_DAMPER_ON