Reco

Thanks John That's helped but the collective in the cockpit is increasing but not decreasing when rolling back collective. The hardware collective is doing what it's supposed to.when I roll on the throttle the N2 gauge increases and when I roll back the n2 decrease the cockpit collective stays in the full position I am in the process of re connecting my switches as my 32 button interface from Leo Bodnar has turned up and I am tidying up my cockpit wiring I will remove the ini file and start from scratch with a clean one and start re assign my switches and rotary encoders to tidy everything up. Cheers Rhys

Hi John Good news its now working the minor error in the script fixed it. How do I reverse the axis, the throttle in the cockpit is opposite to my hardware throttle Cheers Rhys

Thanks John I will correct the issues you have pointed out.I always assumed that the modules folders was the installation folder I really appreciate your time and help Regards Rhys

Hi John I have included my ini file Added the Auto to the ini file and set axis to send to FSUIPC offset and lua file is in my installation folder but no joy Cheers so far for your help Rhys FSUIPC4.ini

Hi John Sorry struggling on this ,adding a Macro is about my limit of knowledge when it comes to programming. I can transfer the zip file I have for you to look at at your convenience Cheers Rhys

Hi John Here is the file, but might need your help on 2 things if are able to. One switch I just can not seem to find in the variables list Plus the collective throttle shows up as 85859 ( L:UH1_THROTTLE = 0.000000) as the throttle is a axis and not a switch I am not sure what to do. In axis assignments I have mapped my collective throttle to pro pitch1 and when I rotate it, the engine spools up but the collective throttle in the 3d cockpit sits in the idle position so I have to use the mouse to rotate the collective throttle to get the N2 needle gauge to get to full for take off Pm a email and I can send you the files Cheers Rhys Bell_UH1C.mcro

Hi John Thanks heaps for your help. with some perseverance I created a new macro and placed all the switch commands into it and eventually found the correct one. I have also been able to assign switches in another aircraft using the local panel variables that in the past could not assign Cheers Rhys

Hi John I can send you the freeware fsx se version Installer I have found on my old PC. I thought the newer version at Blackbird freebies was an updated version for fsx se but it was only for p3d. I can add a image of the switch on the panel which I am having trouble with. Let me know the best way to send you the file Regards Rhys

Hi John Sim is fsx se the aircraft is the now freeware Milviz Bell uh1 redux. Cheers Rhys

Hi I have an aircraft that has switches that I would like to assign to my cockpit but after running the logging console window non of the switches show any command when I move the switch in the 3d cockpit. I ran list local panel variables and the log files shows up lots of commands. I have made a macro file and managed to go through and get several switches working and moving in the 3d cockpit and doing that they should One switch however I just can't seem the locate. Is it possible that while I can move the switch with the mouse in the 3d cockpit, it is not located in list local panel variables with all the other commands. Cheers Rhys

Thanks John I have reverted back to an earlier version which accepts fsuipc to assign cyclic controls via aileron elevator and also axis cyclic longitudinal and lateral I posted a bug report regarding the cyclic issue. Cheers Rhys

Hi Thanks for the replies So the Axis Cyclic Lateral/Longitudinal Set controls don't work? Yes tried that and they don't work. The pedals and throttle (collective) work in fsuipc just not the cyclic. in the log it does show the control events So I have gone back to using MSFS2020 setup for the cyclic. I have include a zip file as the log file exceeded 4.88 MB Nervac have you noticed with the MD that if you start at parking spot with the engines off that the red fuel valve and the ignition car are in the on position ? Cheers Rhys FSUIPC7.zip

Hi I am using MSFS2020 and own the cowansim Md500e but I am having problems assigning the cyclic inputs via fsuipc. Back in the fsx days I would assign the cyclic the aileron and elevator untick enable controllers and everything was fine. Reading through the cowansin pdf manual it says Cyclic Stick: You can use the default aileron and elevator axis for the cyclic, but it is recommended to use the provided SET CYCLIC LONGITUDINAL & LATERAL AXIS. I have set the cyclic to aileron and elevator in fsuipc and send to fsuipc direct calibration but the control are not responding. I can assign the controls via the MSFS2020 control options but it is so clunky to use the interface. Cheers Rhys

Hi John Yes the .evt works with fsx. I have never used a .evt file before. It covers all the systems for the dodo 206. I will contact the person who made it available to me and ask to put it here I would like to thank you for your time and help on this it is very much appreciated. The info you provided helps answer questions if I come across any similar issues in the future Kind regards Rhys

Hi John Thank you for all your help on this all the same and the explanation. Cheers Rhys

Hi John I have include images of what I get when I press the Wrn mute button and dir gyro toggle I had a read through the documentation on Macros and when I press the tab to check if the macro is working nothing happens. Cheers Rhys

Thanks John I'm away from the sim so will try out what you have given me tomorrow. The 23 was at the end of the RX746f0*X55cc. So didn't edit the file I am using the 2d panel when I run the macro I will report back tomorrow to let you know how I get on. Thanks for your time and help Cheers Rhys

Thanks John My bad regarding logging Will try as per your suggestions Cheers Rhys

Hi John Thanks for reply . I have included my Macro file. Had a look at the documentation that includes a list of fsuipc commands but they relate to the p3d version as there is a .Evt File which is not in the fsx version The following are Directional gyro & attitude indicator: Fsuipc Applicable custom events= DIR_GYRO_SWITCH_TOGGLE Warning horn mute button: Fsuipc Applicable custom events= WARNING_MUTE_BUTTON_TRIGGER Annunciator (caution lights) test button: Fsuipc Applicable custom events= ANNUNCIATOR_TEST_BUTTON_TRIGGER These custom events are not in the fsuipc version for fsx or fsx se I ran the logging event window but when I pressed on the cockpit button nothing showed up in the fsuipc log window. Cheers Rhys Dodosim206.MCRO

Hi I'm trying to create a mouse macro for the dodosims 206 to operate the :Horn mute :Direction gyro :Annunciator test panel I have gone to button and switches and click create macro named it, pressed ok and ok on the main fusipc window. In the 2d panel I click on the button and I get the macro window appear top left of screen, name the macro eg horn mute got back to fsuipc click end macro. My Marco appears in the controls drop down box but when I assign it to a switch it doesn't work. Cheers Rhys

Hi John, thank you. Looked at my setup this morning and changed my assignments for the dodosim 206 to send direct to fsuipc calibration. Everything is working as it should now. once again thank you Rhys

Hi I have downloaded the now free dodosim bell 206. As I start to set up the cyclic, pedals and collective controls it seems that choosing :send to FS as normal axis and select the axis aileron, axis elevator and axis pedals is the way to go, at least for this aircraft. If I used the option to: send direct to fsuipc calibration and select aileron elevator and pedals the elevator at least doesn't respond like it should. My other helicopters I have in my hanger are set up via the send direct to fsuipc calibration. So my question is, should I set all my other helicopters to : send to FS as normal.axis. And is there any advantages or disadvantages to doing so Regards Rhys

PM Sent Cheers Rhys

Thanks John Maybe the developer will add this and other small issues in future updates Regards Rhys

Hi. I know you must be busy and have lots of requests but was wondering if at any time in the future is it possible to add "Set Helicopter Throttle Axis". I fly the cowansim MD500e and mapped about 80% of the cockpit controls via fsuipc. The twist throttle on the collective which used to be pitchprop in FSX is " Set Helicopter Throttle Axis". I find the axis controls setup in msfs2020 no where near as straight forward as fsuipc. Cheers Rhys