OY-VKG

Hi Pete I finally found out why this wasn`t working The Advanced User Guide states the following. You can have one condition, as shown above, or two, or more (up to 16 in fact), like this: n=CP(F+j2,b2)(F+j3,b3)j,b, .... where, now, both the parenthesised conditions must be met for the ‗j,b‘ button action to result in the defined event. The Correct formatting is as follows n=CP(F+j2,b2)(F+j3,b3)j,b, .... For each paranthesis have to have the "F" before this works correct. Regards Jesper

The key used for the compound are as follows 332=N192,8,1003,281,1004,281 333=N192,9,1003,282,1004,282 334=N192,10,1003,283,1004,283 335=N192,11,1003,284,1004,284 Its the same key only to be shifted, controlled or shifted and controlled. Can this be why it works both switched when fx the trigger key is shifted? Jesper

OK thanks It seems that 16 to 19 are being activated when only 20 & 21 should be active? 16=CP(F+1,25)1,4,CM1:47,0 17=CR(F-1,25)1,4,CM1:50,0 18=CP(F+1,25)1,5,CM1:48,0 19=CR(F-1,25)1,5,CM1:49,0 20=CP(F+1,26)(F-1,25)1,4,CM1:51,0 21=CP(F-1,26)(F-1,25)1,5,CM1:51,0 Regards Jesper

Pete One more... Can I use Flags together with conditions?? See exampel below 16=CP(F+1,25)1,4,CM1:47,0 17=CR(F-1,25)1,4,CM1:50,0 18=CP(F+1,25)1,5,CM1:48,0 19=CR(F-1,25)1,5,CM1:49,0 20=CP(F+1,26)(F-1,25)1,4,CM1:51,0 21=CP(F-1,26)(F-1,25)1,5,CM1:51,0 Can`t get it to work. Jesper

OK I finally GOT it - The trick was to use a button that doesn`t exist physically and use the SET and CLEAR flags :) Thanks again Regards Jesper

Hi Pete It`s not that i`m avoiding the easy keys - i`d just like to use a key on th left hand side of my keyboard as an press and hold switch while using the controller button alternate functions. And CapsLock, Shift and Tab are all on that side by design :) I`ve got it working by using another controller button (1,11)with a flag (see below) but cannot get it to work by using a keyboard press and hold function instead of the controller switch?? -- FCU SPD -- 6=CP(F+1,11)1,0,CM1:39,0 7=CR(F-1,11)1,0,CM1:41,0 8=CP(F+1,11)1,1,CM1:40,0 9=CR(F-1,11)1,1,CM1:42,0 -- FCU HDG -- 10=CP(F+1,11)1,2,CM1:43,0 11=CR(F-1,11)1,2,CM1:45,0 12=CP(F+1,11)1,3,CM1:44,0 13=CR(F-1,11)1,3,CM1:46,0 -- FCU ALT -- 14=CP(F+1,11)1,4,CM1:47,0 15=CR(F-1,11)1,4,CM1:50,0 16=CP(F+1,11)1,5,CM1:48,0 17=CR(F-1,11)1,5,CM1:49,0 -- FCU V/S -- 19=CP(F+1,11)1,6,CM1:52,0 20=CR(F-1,11)1,6,CM1:54,0 21=CP(F+1,11)1,7,CM1:53,0 22=CR(F-1,11)1,7,CM1:55,0 Regards Jesper

OK I see. I`m fiddling with the compound and flag toggles now - i`m trying to use CAPSLOCK (K20) as the toggle key... But I`m having trouble. Also I`m trying to make it work with macros. Regards Jesper

Hi Pete Thanks for the reply So you`re saying that it`s not possible to use either shift or control for setting this flag? I was actually just reading through the section about compounds in the Advanced User Guide :) Regards Jesper

Hi Pete I was wondering about the possibility to make my CH Throttle Quadrant work in combination with my keyboard shift and control keys. I don`t know whether you are familiar with the CH throttle? I would like to be able to use the little up/down buttons on the front work in conjuction with Shift and Control on the keyboard. To have multiple functions on each button. I know the the CH manager GUI has the function to use another button the controller as a shift button - but I don`t want to use a button for this. It seems that this is not possible in FSUIPC ver. 3.93 It would give some extra key functions. Any ideas? Regards Jesper Hansen

Hi Pete Thanks for the quick answer. I will try your suggestions. Thanks again. Jesper

Hi Pete Just wondering why keys like ESC, Windows Key etc. are not availble in FSUIPC? I'd like to be able to program keys using these combinations. Regards Jesper