STF-DIR

Hello Pete, thanks for the Answer, but i dont understand what you mean about the SetBit and ClearBit ? Where and How can/must i do that? In the FSUIPC Window i have not found some equal? And also what is a Lua plug-in ?? This http://www.artweaver.de/lua-plug-in-de/ ?? Matthias

Hello Pete, thanks for the fast answer !! Its the PMDG and here are in your Macro ( and the PMDG Software ) only a Toggle for the Logo Lights. I have testet the Landing Lightsit works. ( Programmed the FS9 Landing Lights OFF to the Button OFF and ON to ON ) But there are no offset for the Strobes / Logo / ACL - Lights in the FS9. Do you know a software scanning the Hardware Positions of the BU0836X and send the Actual Positions over the FSUIPC to the FS ? Matthias

Hello, a short question: How can i provide that a Hardware Switch (ON/ON) connected on the BU0836X from Leo http://www.leobodnar.com/products/BU0836X/ always is in the same position as the switch in the Cockpit ? For example the Landing Lights of an PMDG737: HWS - Hardware Switch SWS - The Switch in the Cockpit HWS = OFF , SWS = OFF now set the HWS to on, ok, HWS = ON and SWS is also ON BUT NOW I TAKE THE MOUSE AND SET THE SWS TO OFF !!! Now the HWS is ON and the SWS is OFF. When i now set the HWS to OFF the SWS switches to ON. This is exactly the wrong direction of the Switches. What can i do here ? Matthias

Hello, a question: Can i read the Values for the Power Panel on the left top of the Overhead Panel of the PMDG 737NG read by FSUIPC Offsets? I am on the Way to build n Hardware Overhead Panel. This is what i mean : Mattjhias

Hello Pete, its the aktual 3.96. Matthias

Hello, my FS2004 crashes if i have the FSUIPC Buttons + Switches Page open for a While. ( 1 or 2 Minutes ) What can it be, what can help here ? Matthias

Hello Pete, yes it works perfekt with default Aircrafts. Is her absolutely no way to read this Values ? Matthias

Hello, i try to read the AP HDG Bug setting in my PSS757 ( Offset 07CC 2 Autopilot heading value, as degrees*65536/360 Ok Ok) But the result is every time 0. When i change the Aircraft eg. to the Beachkraft 350 it works. What i', doing wrong? Matthias

Hi Pete, ahh thats what you mean. Ok, but try to fly online, its a lot of fun on all Networks. Matthias

Sorry for the bad english Pete. That will mean "Ahhhhhhhhhh, you fly with the SB3. I not using the SB3." you understand now.. i hope :-) But about your question i can not answer. You must ask the IVAO Staff about that. Matthias

Hi Pete, a you fly with the me unknown SB3. Take a close look to the IVAO Software. Its not bad. Matthias

He Pete, you do not fly online ??? Then its now Time for that .. its a lot of Fun !! Yes the Checklist, but you know .. difference between the real flight and the hobby flight :-) I fly on the IVAO networt, so i use the IVAP, IVAC for controlling and IVAE to see other Pilots and ATC Stations. Matthias

Hi Pete, ( i am flying myself a C172 ) i know about the IAS and the Wind :-) About the automatic Transponder setting: I also so often vorget to set the Transponder to Mode C ( only on the Simulation :D ) so i want to make it a litle bit easear for the Pilots in my VA, thats all. Matthias

Hi Pete, thanks for the Answer. I think i will take the GS or IAS and when its over 30kt or the OnGround Flag says the AC is airborn i will turn on the Transponder. I think thats the easyer way. Matthias

Hi Pete, hmm, that are not the news i want to hear from :-( I need it for a litle Black Box Programm i am try to create in c# for my Virtual Airline. So i can different between the Aircraft is on the Ground or not. I know the OnGround Flag, but better for me was a Offset, or a calculatet Value, that shows me the correct radio altitude 0 if the Airplane stands on his Gear. Onothe Question is the Squawk setting. On Ivao ( and also in Real Live ) Pilots sets the SQ to Mode C if they line up the Runway. Now the IVAP ( IVAO's Pilot Client ) has an Offset reading/writing the SQ to Mode C or Stand by. Now i want to different if the Airplane is on the Runway or not. Is there any way ? Matthias

Hello Forum, i am searching an Offset showing me 0.0 if a stand with every Aircraft on the Ground and shows me the Altitude over the Ground in flight. The 0x31E4, called Radio Altitude, shows me 2.4 in the Beachkraft and 7.7 in the B737-400. Is there an offset showing me 0.0 in every Airplane over the Ground or is there a way to calculate it ? Thanks Matthias Programming in C#

Hi Pete, we have posted at the same time , sorry. This message comes from a user of my flightplanner software. I have registered a external exe programm named stf_accars.exe , but the new name is FlightPlanner.exe and has many more and other funktions. So i need again a freeware key from you for: program name : STF-FlightPlanner the “Company” : Starflight-virtual The “Product Name” : STF-FlightPlanner The “File Description” : STF-FlightPlanner Please generate a new key for me. thanks Matthias please send it to webmaster@starflight-virtual.de

...add to my Message: I have tried again : Start FS2004 where FSUIPC 3.70 ( also tried v3.65 ) is installed and Registered. The i have tried to start my Application...it will not work and brings up the Message that FSUIPC can not be found. Then i have now tried to start IVAO's IVAP and it will also not be working ! I have the Screenshots for you and also again the Log File added. Matthias Log:

Hello, after i have installed FSX anf FSUIPC 4 i can not connect to my FS9 installed FSUIPC 3.70 ?? Also IVAP brings up a Message that he can not connect to FSUIPC . Whats here wrong Pete ? Matthias PS.: here the Log file This Line comes every Time i try to connect to FSUIPC ( runninig FS9 )