Morteza Ghasemi

Yes. No. I look into FSUIPC for Programmers.doc for Battery and alternator switch and their size. No. There isn't any error. Yes I'm using FS98, FS2000, FS2002, FS2004 and CFS2 on four last year. and trying to build flight training devices for trainner aircrafts (Bell-206 , Bell-205, MFI-17, Cessna , and Tukano). Cessna and Extera 300S and all other aircraft works like bell-206. You can try it on Extera-300s beacouse there is two independent switch for both battery and alternator switch on it's panel. I Build two XML Gauge for Battery and Alternator switch as follow and place them on Bell206 panel (A:General eng1 generator switch,bool) (A:Electrical master battery,bool) My assignment on FSUIPC.ini file is as follow [buttons] 1=P0,20,Cx01003102,x01 2=U0,20,Cx01003102,x00 3=P0,19,Cx01003101,x01 4=U0,19,Cx01003101,x00 But when I turn generator OFF. Battery switch Turn OFF too. Battery switch control is Toggle and depends on starting flight. so I can not assign it to a switch so that OFF position on down and ON position on UP. I use alternator switch like battery swith without any reason. If I write on 3101 and 3102 Offsets Both, I can operate Battery and alternator together. [buttons] 1=P0,1,Cx01003101,x0101 2=U0,1,Cx01003101,x0000 I assign two XML gauge for Battery and Alternator switch and place them on bell206 panel. and test them using external switches. Regards, Morteza

Dear pete Thank you for your help. I'm Trying to build a Flight Training Devive for Bell 206 Jetranger III . I Assign Offset Byte Set 0x3102 for battery switch and Offset Byte Set 0x3101 for Generator switch. but this error occured. After reading your responce I trying to change address of offset and assign following addresses: Offset DWord Set 0x3B78 for Generator Offset DWord Set 0x281C for Battery Switch Now i haven't any problem and Battery and Generator Switch work correctly and seperately. Thanks anyway regards Morteza

Hello Dear Dowson When Battery switch is ON and I change Alternator(generator) To ON, battery switch automatically goes to OFF so that when i make alternator OFF, Electrical system fails. I want Battery switch does not go to OFF automatically when i start alternator. Thanks Morteza Ghasemi

Yes. I need some graphics view from main rotor. From Virtual Cockpit view I can see main rotor but on cockpit view main rotor isn't visible on forward view. I want to see Main Rotor when i Zoom out on cockpit view (look forward). Thanks Morteza Ghasemi

Hello How can i view main rotor from Bell jetranger 206 cickpit view on top of the screen. Best regards Morteza Ghasemi

Hello How can I activate IDLE RELEASE Button. I use Prop for when thrrottle is above the IDLE and mixture for when throttle is belove the IDLE position both for helicopter but when i decrease mixture it does not effect until mixture is zero . and then fuel switch go to OFF position and when increase it become ON. its seem that IDLE RELEASE button works automatically. I want to convert it to a manual button or key. Thanks Morteza Ghasemi

Hello I can not find "AICRAFT EXIT" offset on FSUIPC. How can i set Aircraft Exit Open or close seperately not toggle control. also How can I close or open aircraft exits immediately so that delay time become zero. I need to close doors of airplane and lock them. so that when door is closed and locked, Doors warning light Be OFF. Aircraft exit control is a toggle control so i can not assign it to a switch and also this control acts with at least one second delay time and there isn,t this delay time on the aircraft. when i close door and lock them warning Light immediately become OFF. Morteza Ghasemi