150245

thanks will study the documentation thansks rgds CJK

thanks for reply the interface is marked as USB joysrtick and recognized by windos as generic joystick and welcomed by FSUIPC so everything should be ok I do have the >Lvars but do not know where to put in fsuipc or spad next regards CJK

hi there, I realize that I am a little late in replying to this subject but the question has raised only after I installed MSFS 2020 early this year. I do have a Hardware Ecam equipped with an interface but still i can not figure out how to connect via FSUIPC, or where to put the above commands within fsuipc lastest edition of registered FSUIPC is installed thanks in advance for kind assistance regards CJK

hi, thanks for prompt reply. I am flying the PSS Airbusses and after your reply I checked the PSS panel config (should have done before asking silly questions) and found a instruction there how to manage. Now it works sorry if any inconvenience caused regards CJK

hi there and happy new year, I want to know where my mistake is!!! Like to use the autobrake set function with a button. I did programm already lots of them, but this time it does not happen. Selected FSUIPC, pressed the relevant button, select FScontrol, choosed from drop down autobrake set, set parameter to 5 that`s it unfortunately without any reaction. thanks in advance for kind attention and reply regards CJK

hello, thanks for prompt reply. I know that one can handle the flaps with a Potentiometer via Joystickaxes and set by FSUIPC it worked quiet well for long time but know i am facing a bug as the Flaps are automatically moving up when reaching a certain speed, but instead of up they are moving to full. This does not happen if I set by buttons therefore my idea to manage the Flaps by buttons. If it will not work just bad luck regards CJK

Hi Pete, could you please give me a small tip how to toggle the 6 position (PSS)Airbusflaps by buttons? I found in FSUIPC Flaps up, down, 1,2,3 which are only 5 pos. thanks in advance regards CJK

hi, this settings go with all panels, except with the PSS panels which are not working with knob inputs only with mouse clicks. in this case i am using the Airbus A-320 panel Version 1 for FS 2004. By Hector Molina which works fine in 2002 as well. please inform where I can find the technical page as in the FSUIPC config editor site there is only a line saying FixControlAccel=No. I will inform Hector also and ask whether one can alter this in the panel cfg regards CJK

hi, when I set Speed/Heading/Alt/VS with knobs using FSUIPC and input Ap Alt Var dec resp inc and same for speed etc it works in 10 times for speed and heading in 100 for V/S and 1000 for Alt. There is no difference if i use normal or the fast version. now my question: can i alter this in the FSUIPC and if, how? or do i have to alter the panel. cfg. i woul like to have 10 for speed, 1 for heading, 100 for alt and VS. Thank in advance for kind attention. regards CJK

hi pete, with crossover i mean that although i have different knows assigned to different executions i.e. knob 6 to gear up, knob 8 to strobe lights and knob 9 to pushback it could happen that knob 6 toggle strobe and gear up thats what i meant with crossover. from your last message i understand that the key facilities are somewhat stronger. Should i change all inputs to be done via keystroke, which could be possible as well (mabe apart from startup engines and mixture) thanks in advance regards CJK

hi pete, thats me again. you are right i was talking about inputs for the FS 2002. before i allocated the knobs i cleared all the options under FS, but i was mixing up inputs via FS controll and FSUIPC. Could that be the reason for the crossover? thanks in advance regards CJK

hi Pete, i am facing a small problem. for inputs i use the knobs of several USB joysticks. two of them are of the same kind. could it be that for that reasons that i get double functions/crossovers when pushing the knobs for the commands? and if so, how could i solve it apart from the fact simply to change this one. thanks in advance regards CJK

hi pete, i know it is a difficult with those people who believe they are experts, but in fact they are not, like me. to cut a long story short. I use the panel of A 320 pro from just flight in which you can toggle different views unlock the pictures and put same to differents monitors. So i made a screenshot of the OHP copied that to a piece of paper put this on a carton and fixed it to the top of the screen. So i have a nice looking picture without any function. But, with the fsuipc i can use some switches via the joystick and toggle i.e. landing lights, nav and beacon etc. by just putting switches into this picture. all is possible and functioned but not the seatbelt and non smoking signes as there is no possibility to allocate a button. and of course i can still toggle the OHP to my normal screen and switch the knobs with the mouse, after having done that i clear the mainscreen and stop. that was when i said it is a bit stupid to toggle the OHP back and force to switch the signes nevermind i will survive even if i dont here the nice ding, dong regards CJK

hi, thanks Richard but please tell me how to arrange as this seatbelt signs i can only toggle via the overheadpanel i.e. I have first to toggle popup the ohp and than i can switch the signs on. As i am building an OHP it looks a bit silly to do this procedure, than its better just to forget. anyway thanks and if I did misunderstood you please tell me regards CJK

hi, how to toggle the fasten seat belt signes with a button/switch? in fsuipc i did not found a allocation within all the hundreds of names thanks in advance regards CJK