cmgam
-
Posts
42 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Downloads
Posts posted by cmgam
-
-
Hi
I need some help to calibrate my Pro Flight Yoke System because, on axis calibration there are no differences between the "min" and "mid" positions. The numbers are the same then, I can't set reverse, props feather and cut off mixture.
On CH products I know that there are a "DetentValue" that I must set but on Saitek products I don't know how to do it if the same problems exists.
Whith thrust reverse, I "walked around" using F2 key on "buttons + switches" but for prop feather and mixture cut off, I don't know how to do it so the need of help :oops:
I have FS9, Vista 64 and the last drivers for Pro flight system.
Many thanks in advance
Regards
cmgam
-
Hi
Just to say that now, after your advices, everything is working. :D
Thanks again
Regards
cmgam
-
Hi peterhayes and Bob Church
I use Control Manager in direct mode; I'll follow your advices and suggestions as soon as I get home. :)
Many thanks to you,
Regards
cmgam
-
Hi peterhayes and Bob Church
I'll follow your advices as soon as I get home. :)
Many thanks to you,
Regards
-
Hi
I would like to have your help for the following problem with FSuipc and CH quadrant.
I have FS2004 (FS9.1) and the lastest version (registred) of your software.
After some weeks of inactivity with FS, I resumed my flights to find that my throttle quadrant needs a new setup (before, everything - quadrant, FSUIPC, etc. - works OK).
I followed the Jonh Cook tutorial but at not avail.
The problem is when I try to assign ANY axis to ANY Joy# of CH quadrant, the FSUIPC cannot record any difference between the detent position of the joy# and the "min" position, i.e., on any axis/joysick, the FSUIPC values - on Axis Assignment and Joystick Calibration modules - are (numeric values can change):
MAX position of the joystick: in: 16386
out:16383
Detent position of the joystick: in: -16384
out: -16384
"Min" position of ths joy: the above (same) detent values :shock: !
As I said and you can see, there are no diferences between the 2 lowers positions so I can't calibrate the joystick inside FSUIPC (Reverse/idle).
I have joystick disabled on FS;
I unistall all the CH products I have (Rudder pedals, yoke and quadrant) and clean the win registry of any CH key and made a new install;
I have the quadrant calibrated with CHManager (where the 3 positions are verified and checked);
I delete the FSUIPC.ini and created a new but nothing changes :(
Any help? :)
Many thanks in advance
Regards
cmgam
-
Hi
Same here :evil: .
If I use my multiplayer session without connecting FSnav to the session, everything goes OK but, if I connect Fsnav to that session, at the end of the flight, when I want to disconnect (doesn't matter how I disconnect it - fsnav first or not) everything hangs and only thru "task manager" I can kill Fs9.
Any ideas :wink:
thanks in advance
Regards
cmg
Saitek Pro Flight Help!
in FSUIPC Support Pete Dowson Modules
Posted
Hi "dconream"
Try these drivers:
ftp://ftp.saitek.com/pub/software/full/rs_pfw.exe
They are working OK on my Vista 64 system :) .
I'm using F2 as "reverser", assigning throttle as Jim Harnes :wink: .
"Feathering" propellers, as you, I don't know how to do it :? .
Regards
cmgam