lorenzoc3

FSUICP4 ADVANCED USER ( for FSUICP version 4.86 Fe4bruary 2013) Multiple Joysticks for multiple pilot still pag 45 Me Pete . If you will be so kind to let me have the new manual for advancer user in order to apply method 2. I have already done that but nothing happens - mobile surface still fluttering regrads

I downloaded the last version of FSIUCP4 and it is sure, the manual is on the folder FSICP4 's documents i will check and revert tks and regards

Soirry sorry, sorri Mr Pete D. but many time anxiety and fear of not being understood cause many fatal errors. I will try to explain again steep by steep of course you dont know what i am doing therefore i must be able to indicate you what and what i need from you : 1) FS X with relkevant service pack ; 2) Your FSIUCP4 last version February 2013 4,86 3) Multiple joisticks for pilot and copilot ( your manual for advanced user pag 45 ) Method 1 4) FSICUP4 installed and registered ; 5) start FSX - alla peripheral alredy connected through the port usb2 with 5 axes each one AILERON , ELEVATOR, DIFF BRAKE RIGHT AND LEFT , RUDDER LEFT CENTER RIGHT; 5 axes for both pilot station 6) panel in fsx for peripheral calibration Off and all axes erased; 7) i proceed with axis assignment send direct to fsiucp for calibration. :cool: the first station is ok !! as soon i try with the second station to assign axis all surface have a flutter. 9) I take as a guide section of your manual pag 45 Method 1 10) can you be so kind to explain to me above method?? ; it is possible i can not undersatand alla steep to be done and i make a mistake wich generate e flutter. 11) you say .. now add to the FSIUCP4.Ini file's Joy Callibration section a list of decl...... patiently explain to me what should I do?? i would like to send photo but i dont know how to do this from here . many tks for you effort Lorenzo

I thought the chapter where you talk about multy pilot station the list to add to the INI files were used to avoid this problem of jetter in the secoind , third etc... . In fact, where typing the letter B C / D etc. .. to distinguish the multi pilot station and avoid the jetter. It happens as if I setting a peripheral with both control panel ( FSIUCP and FS Panel ) opened . Anyway i would like to check for poor which cams from electronic cards connected to the usb2 of cmptr Tks to you for your effort. reverting tks and regards lorenzo

Good day Mr PETER , i try to explain as best i can. I have two Pilot station ( home built ) with Aileron, elevator, rudder and break right and left for each station. the version of FSIUCP is the last version downloaded from your site just one weeks ago 4,68. during setting the second pilot station with FSIUCP ( sending diretct to FSIUCP for calibration ) as you instruct on you manual i find a jetter ( flutter ) on the axis. how to avoid it ??? i looked for a way to send a foto but without success. Regrads lorenzo

Dear Mr Peter, i am not able to understand this paragrah on your manual ftor dvancer user. i am not able to configure the second pilot station, wichi is very important for my cabin. i have always a flutter as soon as i tray to settle the second station. i followed your instruction reporting also list of second secontroller with letter B and value fron List of controll in the file.INI but withouth to solve the problem. can you pls be so kind to let mi have some more instructions to do that ??? or some check list with the steep to configure second pilot station ??? many tks and regards lorenzo cotroneo

only to nsend you my best whishes for nhappy and propserous new year regards lorenzo

Always tks to you. untill now it is ok - in case of average i will inform yoy at once. by Mr Pete regards lorenzo

You have done to much Dear Peter. the problem is solved and i am very happy and very grateful to you for you kind assistance and help. anyway for you guidance, the value of 250 appears on RAW too, and only after mooving axes it go to 1 or 0 unrtill know i configured two aircraft with all axes and switch and all seems to be ok. I hope to revert only to say good bay to you regards and tks again Mr Pete lorenzo

Hi Mr Pete, i forgot to say you one important thing. whe i open the FSX all axes are stopped owing the delta value , which is alwais to 256 for all axex. after i move them and click on delta switch i reduce value to one or "0" ziro . may be important ??? ciao

RE.: YOUR VERY FAST ANSWER THU APR 22 12.24 pm Not yet started to format. ok i will stop with this. i dont make any drastic opoeration yet as befor said, i have used all your version since FS2004 than now with FSX from the 3.0 to 4.6 for fsx . on 2007 i changed version from 2004 to FSX and sent to you an mail asking for new key rememberes ?? ( it is still on my post) actually i have only this latter version, whit fsx , because , owing to the flutter ,i erased all hold version immaging a conflict. I erased all file .ini too avoid any conflict and restart the calibration, but nothing to do. You say that may be the problem is the RAW mode of the new version ok as you instructde i downloaded alredy the version as on your link ,sent to me ,and after installed and programmed axis and buttom, for one aircraft, i return to you. Tks Mr Pete regards lorenzo

last resort is to format hard drive and install everything again, hoping that the problem does not return as i have not seen the cause. i have to ask sorry to you for the disturb which i gave to you and to send you unthousand of tks for your help and for your effirts. one thing is sure , it is not caused by FSUIPC that i use since the previuos version of 4.0 without problem. tks and regards lorenzo

Hi Mr Pete . tks for your long answer and analysis to my problem not yet solved- I'll try to answer as best I can : 1) Yes i am saying that assigning one buttom ( panel 2/3/4/toggle pushback , view mode, flight map etc... wtc.. ) makes a flutter on the axes ,but now not before tha one week ago. 2) It is possible that the button scanning probably interferes electrically with the analogue readings on the axes. I have a problem but not dected until know and as far as i know not with your FSUICP . 3) I have a programmable digital inputs ( Usb Cards with 10 axes assigned with Raw mode since abt 4/5 years , together with 20 switches with both cards for different actions) whay only now the flutter ??? 4) I have assigned 66421 and 424 axis propeller 1 and 2 - than on right-hand zone assignments facility the prop pitch incr and Decr , for adjusting the pitch of the propellers on fly , and never i got conflict. 5) this has been done also for mixture : in the left t side of FSUICP windows " sento to MSFX like a ..... axis mixture 1 set and axis mixture 2 set , than on right side , incr and decr mixture . without problem antill arriving a flutter i dont know from where. 6) i will do what you say to clea again but i am shore without success. I do not know how to thank you for your help

Hi Mr Pete , After many trials and a new general cleaning of keys in FSX, just to aviod the dual assignement, I tell you the news of the moment or my latest discovery . In this matter, please it is importanto to clarify that you must be sure that i am sure problem it is not caused from FSUICP I ask you help just because you have more experience than me with FS and all which is around to it. after configured, befor only the axes, one by one ,with FSuicp of course, i moved to settle the buttons with my Usb cards which allow 5 axexs each one and 24 buttoms. I proceed button by buttom and test the FSX for eventual flutter. as soon i settle the first buttom flutter started again. erased buttom and stopped flutter,. the usb cards anyway are regular recognisìzed by Windows and by FSUICP as usb perioferal and on test all buttom and axexs are present and without interference. I attached copy of INI.file regarding only one aircraft if you with you experiencde may found some the problem. [General] UpdatedByVersion=4600 History=52GWOU47KCE06TH12WPAI MouseWheelTrim=No MouseWheelTrimSpeed=1 JoystickTimeout=20 PollGFTQ6=Yes BlankDisplays=No FixControlAccel=No FixMachSpeedBug=No VisibilityOptions=No OneCloudLayer=No CloudTurbulence=No CloudIcing=No GenerateCirrus=No SuppressCloudTurbulence=No MaxIce=-4 MinIce=-1 UpperWindGusts=No SuppressWindTurbulence=No SuppressWindVariance=No WindTurbulence=No TurbulenceRate=1.0,5.0 TurbulenceDivisor=20,20,40,40 SuppressAllGusts=No MaxSurfaceWind=0 WindLimitLevel=200 WindDiscardLevel=400 WindAjustAltitude=No WindAjustAltitudeBy=2000 SmoothBySimTime=No WindSmoothing=No WindSmoothness=2 WindSmoothAirborneOnly=Yes PressureSmoothness=0 TemperatureSmoothness=0 DisconnTrimForAP=No ZeroElevForAPAlt=No ThrottleSyncAll=No WhiteMessages=No ShowPMcontrols=No SpoilerIncrement=512 MagicBattery=No RudderSpikeRemoval=No ElevatorSpikeRemoval=No AileronSpikeRemoval=No ReversedElevatorTrim=No ClockSync=No ClockSyncMins=5 ClearWeatherDynamics=No OwnWeatherChanges=No TimeForSelect=4 LoadFlightMenu=No LoadPlanMenu=No PauseAfterCrash=No BrakeReleaseThreshold=75 SaveDataWithFlights=No ZapSound=firework ShortAircraftNameOk=No UseProfiles=No TCASid=Flight TCASrange=40 AxisCalibration=No DirectAxesToCalibs=No ShowMultilineWindow=Yes SuppressSingleline=No SuppressMultilineFS=No AxisIntercepts=No DontResetAxes=No WeatherReadFactor=2 WeatherRewriteSeconds=1 CustomWeatherModify=No SimConnectStallTime=1 [JoyNames] AutoAssignLetters=No 0=IOCa 0.GUID={D89EC0E0-FFC0-11DE-8002-444553540000} 1=IOCa 1.GUID={D89EC0E0-FFC0-11DE-8003-444553540000} [buttons] ButtonRepeat=20,10 [AutoSave] AutoSaveEnabled=No [GPSout] GPSoutEnabled=No Port=COM1 Speed=4800 Interval=2000 PosTo6Decimal=No Sentences= [GPSout2] GPSoutEnabled=No Port= Speed=4800 Interval=2000 PosTo6Decimal=No Sentences= [WideServer] WideFSenabled=Yes [Axes.Beech King Air 350 Paint1] 0=0X,R0,F,66421,66424,0,0 1=0X,B,-127,0,65769,0 2=0X,B,0,127,65771,0 3=0Y,R0,F,66731,0,0,0 4=0Y,B,0,127,66277,0 5=0Y,B,-127,0,66276,0 6=0R,R0,F,66732,0,0,0 7=0R,B,0,127,66279,0 8=0R,B,-127,0,66278,0 9=0S,R0,F,66422,66425,0,0 10=0S,B,-127,0,65775,0 11=0S,B,0,127,65777,0 12=1X,R1,F,65763,0,0,0 13=1X,B,20,30,65686,0 14=1X,B,-10,20,65687,0 15=1X,B,30,60,65685,0 16=1Y,R1,F,65762,0,0,0 17=1Y,B,-127,-21,65684,0 18=1Y,B,20,127,65683,0 19=1Z,R1,F,65764,0,0,0 20=1Z,B,-5,5,65689,0 21=1Z,B,5,32,65690,0 22=1Z,B,-39,-5,65688,0 23=1R,R0,F,66420,0,0,0 24=1R,B,-126,42,66420,0 25=1S,R0,F,66423,0,0,0 26=1S,B,-127,56,66423,0 [JoystickCalibration.Beech King Air 350 Paint1] AllowSuppressForPFCquad=Yes ExcludeThrottleSet=Yes ExcludeMixtureSet=Yes ExcludePropPitchSet=Yes SepRevsJetsOnly=No ApplyHeloTrim=No UseAxisControlsForNRZ=No FlapsSetControl=0 FlapDetents=No ReverserControl=66292 Reverser1Control=66422 Reverser2Control=66425 Reverser3Control=66428 Reverser4Control=66431 MaxThrottleForReverser=256 AileronTrimControl=66731 RudderTrimControl=66732 CowlFlaps1Control=66162 CowlFlaps2Control=66163 CowlFlaps3Control=66164 CowlFlaps4Control=66165 SteeringTillerControl=0 MaxSteerSpeed=60 Aileron=-10,25,25,60/8 Elevator=-127,0,0,127/8 Rudder=-41,3,3,34/24 Throttle1=-124,-47,-47,36 Throttle2=-122,-48,-48,50 Mixture1=-127,0,0,127/8 Mixture2=-127,0,0,127/8 PropPitch1=-127,0,0,127/8 PropPitch2=-127,0,0,127/8 Aileron Trim=-127,0,0,127 Rudder Trim=-127,-1,-1,127 [buttons.Beech King Air 350 Paint1] 12=P1,16,C66079,0 13=P1,17,C66080,0 14=P1,2,C65759,0 15=P1,5,C65758,0 16=R1,7,C65607,0 17=R1,6,C65615,0 18=P0,7,C65909,0 19=P0,6,C65908,0 20=P0,5,C66432,0 21=P0,10,C65907,0 22=P0,0,C65911,0 23=P0,3,C65567,0 24=P0,1,C66483,0 25=P0,11,C65794,0 26=P0,12,C65795,0 27=P0,4,C66615,0 28=P0,2,C66616,0 29=P1,4,C66609,0 30=P1,21,C66617,0 31=P1,20,C66612,0 32=P1,19,C66604,0 33=P1,18,C66620,0 34=P1,3,C66605,0 35=P1,1,C66625,0 36=P1,0,C66624,0 37=P1,23,C66626,0 38=P1,22,C66623,0 Ciao Mr Pete