eric737

Hi Pete I assign gear up and gear down not toggle, elevator trim up and trim down I try to assign the same way? Thanks for your help will see if I find the solution with Ifly737

sorry, firstly FSX and ifly 737 ,what is confusing that the switches are recognized by FSUIPC but when assigned to the repective controls( gear up/down and elevator trim up/down the function has no effect on the ifly 737? Thanks Eric

I am trying to get certain functions to work with FSUIPC , for instance LDG up/down the switches are recognized but in the ifly 737 the gear does not work? any suggestions the same goes for the Horizontal stabilizer trim up/down

Looking at the console it has his own driver , however if I connect the 2 pot to a bodnar card I still have no luck to get the assignment done , yes it uses PFChid.DLL

The unit is a PFC C2 professional?

Hi Pete I have an issue with my PFC console ,I am unable to assign the aileron and elevator through FSUIPC , what is happening whenever I fly I get sudden unexpected aileron deflection and can not get rid of it. The PFC has normal sensors but has an internal calibration system ? Thanks Eric

Hi Pete I will try this but as I am looking in your FSUIPC instructions it says that you should disable the controller in FSX , by doing so I loose all functions such as Bodnar switches and inputs , however even so with this disabled I still get erratic inputs? Eric

Hello I have a big issue with flying various AC on FSX , all flight control settings are made through FSUIPC , however without any reason or movement the AC gets out of control and looks like a freak control input which is very hard to control , I have tried all possibilities but so far no luck?

Hi Pete I have a confused set up in FSUIPC : When I fly the AC all over sudden banks right and is uncontrollable ,I am trying to calibrate the aileron and the elevator in FSUIPC , in the section Axis assignment the elevator and aileron is not visible? however when I click on Joystick calibration the both of them are seen by FSUIPC , normally it should be visible under axis assignment but does not show direct? Is it possible because the PFC console is interfering somehow? I am using latest FSUIPC and FSX Thank you Eric

Thanks Pete Will try and hope it works

Hello Pete I have paid for the FSUIPC but due to refurbishing the computer it seems vanished from it? How can I download it again without having to pay for the license again? Thanks Eric

Could you give me a hint how to set up the FSIUPC on my other computer as I have no reg code available? Thanks

Where do I get the code for activation? Thanks

Hello Pete I have already the FSUIPC4 on my first computer , as I am setting up a second FSX setup for my grandson do I need to repurchase a new FSUIPC4 ? Thanks Regards Eric :razz:

Pete I have problems with the starter set up in Ifly737 , the selection in FSUIPC shows starter 1(2) but when the button is assigned nothing happens in Ifly737 , is there a way to make this work? My buttons are connected via Bodnar card ? Thanks

Thanks Pete , will investigate with Ifly documents available Eric

Hi Pete Thanks for a quick reply , I am running Ifly 737 and would like my overhead switches i.e. Starter selection ground to activate the starter on the engine , I have tried both starterset and toggle but neither work? Thanks Eric

Could you give me the correct setting for the overhead starter switches in FSUIPC , is starter set or starter ? Thanks

Thanks will try again

Thanks , but this does not work with my motorized throttle with fuelshut off valves ,I can move fuelshutoff to on but as I said no lightup? There has to be a setting for ignition or mixture?

Could I get some information regarding the setup of the 737 default starting setting, I selected starterset 1 for the left engine and the starter engages , however no light up with fuelvalve open? What is the selection in FSUIPC for ignition? thanks

Thanks , very confusing as I am a bit of a novice about this , on the FSUIPC it normally shows FS window , but only project magenta is available ?

I have downloaded the 737 Driver for the above unit , the unit works except the fuelshut off does not , therefore I am unable to start the engines , the switches are connected to the board , is there a script that can be altered? Thanks keep them flying :idea:

Hi Thomas Thanks for that , the problem is I synchronized the throttle and it works correctly , however I had previously I manual throttle unit from open-cockpit so it may be conflicting the issue? Would you recommend to remove all in connection with the old throttle? Thanks and Regards Eric

Hello I am trying to connect the above throttle unit to my FSX 737 default , however the FSUIPC does not let me assign any buttons? Thanks Eric