ASadik
-
Posts
11 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Downloads
Posts posted by ASadik
-
-
Hi,
I've had this issue before where I have two throttle quadrants (Saitek), but FSUIPC assigns the same GUID to both. So only 1 is read. I had this a long time ago and can't remember how I fixed it. I believe it was to remove something in [joyname], but I'd like to double check. Here is what I have:
In the FSUIPC.txt I see:
94 ---------------------- Joystick Device Scan -----------------------
94 Product= Saitek Pro Flight Quadrant
94 Manufacturer= Saitek
94 Vendor=06A3, Product=0C2D (Version 2.2)
110 GUIDs returned for product: VID_06A3&PID_0C2D:
110 GUID= {0BA51920-4E57-11E7-8004-444553540000}
110 Details: Btns=9, POVs=(0, 0, 0, 0), Cal=x00000000, Max=R0,U0,V0,X255,Y255,Z255
110 GUID= {0BA56740-4E57-11E7-8007-444553540000}
110 Details: Btns=9, POVs=(0, 0, 0, 0), Cal=x00000000, Max=R0,U0,V0,X255,Y255,Z255
110 Product= Saitek Pro Flight Quadrant
110 Manufacturer= Saitek
110 Vendor=06A3, Product=0C2D (Version 2.2)In the FSUIPC.ini I see:
[JoyNames]
AutoAssignLetters=No
2=VKBsim Gladiator
2.GUID={0BA58E50-4E57-11E7-8008-444553540000}
3=Saitek Pro Flight Rudder Pedals
3.GUID={0BA5B560-4E57-11E7-800A-444553540000}
1=Saitek Pro Flight Throttle Quadrant
1.GUID={0BA56740-4E57-11E7-8007-444553540000}
Now I believe I should see two, throttle quads and I delete them, but I can't remember off the top of my head how I was told to solve this before.
Some help would be appreciated.
I did just fresh install windows and etc on my pc, so I don't have the drivers for the saitek devices when writing this.
-
Ok now works fine!
-
19 minutes ago, ASadik said:
Hi Pete,
Same issue with me. But this B update didn't seem to do the trick.
Also I just installed 4955c and that worked fine as well, so for the moment that's what I'm running.
-
8 hours ago, Pete Dowson said:
Please try FSUIPC 4.966b and let me know. Just open the ZIP and copy over the FSUIPC4.DLL into your Modules folder. It is working fine here with multiple Bodnar boards (all i could find here today).
Pete
Hi Pete,
Same issue with me. But this B update didn't seem to do the trick.
-
You need to use FSUIPC 4.946 (or later) with P3D version 3. The Toggle Aircraft Exit control (plus a heap of other controls) were moved into a different table inside the P3D CONTROLS.DLL module!
Pete
Ahh I see. Well I just noticed an update of that as well :) Thank you very much sir!
-
Hi there,
I found that once I installed FSUIPC 4.945a (I think that's the most recent one) into p3d V3 the doors stop working. I can press SHIFT+E + 1,2,3, or 4 and only the main exit is operable. Once removing FSUIPC that issue goes away and all the doors are operable. This is an issue if you're using GSX or need to load payload into Airbus X from aerosoft and so on.
I know Pete is on vacation, but I was wondering do the others that are using FSUIPC on V3 experiencing this?
I'm sure when FSUIPC is actually updated for v3 this won't be a problem, but in case it was also not brought up, I wanted to make it aware as well :)
Thanks,Asif
-
Yes. Persistence pays. The problem isn't so common these days, but it is still some sort of timing conflict in SimConnect. I've not seen it reported yet for FSX-SE (so it's worth trying that),, and I the checks which fail are not applied in P3D.
Pete
Still no luck, however I did receive an error that stated that "multiple FSUIPC were detected" The error suggested removing the modules folder and reinstalling, so I followed that direction. Still attempting to get the timing. I'll let you know what I get out of it, I'm not sure if after a certain amount of time if it's worth just reinstalling all FSX related software or just keep trying? Let me know if you think of anything that could help!
Thank you for the help so far, very appreciated!
-
I'm assuming that this portion is where persistence is needed due to SimConnect conflict?
-
Why did you install the FSUIPC4 Loader? Did you not read the Installation instructions? That is only for special circumstances and generally not advised.
Remove the FSUIPC Loder DLL from the Modules folder, then re-run the Installer.
Pete
FSUIPC Loader was already in the files, I didn't place anything specific in the module files folder manually.
However I removed it and re installed FSUIPC now, and now the error is the same one except instead of asking me to run the loader, it asks for FSUIPC.DLL "Run" or "Don't Run" and then the sim just closes.
-
Hi,
I recently downloaded the BlackBox widebody prologue, and while setting up the load manager for the it asked for FSUIPC to install, which it did. I then made the decision to go and buy the full license for it. I reinstall FSUIPC4 off of the website. After which, when I went to turn on FSX:SE it asked me to verify to run the FSUIPC4_loader.DLL and as soon as I press "run" FSX just closes on the intro screen and my EZDOK gives the message: "FSX Process not found. FSX_Handles: 0"
Usually when I got this error, reinstalling FSUPIC (Free version) just did the trick, but reinstalling doesn't seem to do it this time.Any help would be great,
Thank you much!
Two Saitek Throttle Quadrants only one being read
in FSUIPC Support Pete Dowson Modules
Posted
I am currently using the most recent release on sim market that Pete has put out. I'd assume that's the version. I can check it in the morning.