Jump to content
The simFlight Network Forums

hermann

Members
  • Posts

    34
  • Joined

  • Last visited

About hermann

  • Birthday 04/22/1949

Profile Information

  • Gender
    Male
  • Location
    Austria
  • Interests
    Flightsim, boating, dancing, electronics, Motorized Throttle (TQ)

Recent Profile Visitors

646 profile views

hermann's Achievements

Apprentice

Apprentice (3/14)

  • Dedicated Rare
  • Reacting Well Rare
  • First Post Rare
  • Collaborator Rare
  • Conversation Starter Rare

Recent Badges

0

Reputation

  1. I only have one LED for both red and orange. Is it correct to set 65f1 to 4 byte to switch this LED on in both cases? And the same with 65f5? In the moment it works, but I hope you can confirm it. Rgds Hermann
  2. Hi John, All of these Offsets are working ok now. Thanks for your help 65F1 --- AP red 65F3 --- AP orange 65F5 --- AT red 65F7 --- AT orange 65F9 --- MCP (has orange only) Rgds Hermann
  3. I am sorry, I made a mistake! After leaving the beta-tester- group FS2020 was automatically installed new and all .INI files and the community folder were deleted. And the exe.xml too! After reinstalling FSUIPC everyting is working fine now!! Rgds Hermann
  4. You were right! With SU11 autostart fails again 😞
  5. I think we can close this now: since latest update of fs2020 (beta 11) FSUIPC starts everytime now. Best regards Hermann
  6. Hi John! Sorry for the long delay. Your first solution is working now via Mobiflight: PMDG_B737-7_AUTOTHRUST_TOGA_L_BTN Thanks for all your help and best regards from Austria: Hermann
  7. Hello from Austria! When I set TOGA (I have an own button for it) in PMDG 737-700 it is shown in PFD but in my MotorizedThrottle I cannot receiv it. I use 0x080C 4 AUTOPILOT TAKEOFF POWER ACTIVE but nothing is working. With standard plane the same offset is working ok. I hope someone can help here. Thanks and best regards Hermann
  8. What I see (as Hermann posted) is that the value is always 0, regardless of the state in the virtual cockpit on screen. This is for both the offset as well as the LVar, for all three (A/P, A/T, FMC) In the meantime I found out, that FMC button is ligting up when I use address 65F9 (1 byte) Rgds Hermann
  9. Sorry, but no lamp is lighten. The last offset where a lamp is ok is 65F9. All others below not. These three lamps have an own testswitch: (1) for red and (2) for amber. With this switch only FMC works. But when I use the main-test-switch for the lights, then AP and AT light, but FMC not (what for FMC is ok, I think). So I mean that AP and AT are assigned to some other lights .
  10. I found out till now only: 65FD Speedbrake armed 65FE Speedbrake up 65F9 Main_annunc_FMC 1 Byte The others I will try to find within the next days
  11. *** Moved to FSUIPC7 support sub-forum *** Hello from Austria! As above said, LEDs for A/P P/RST, A/T P/RST, FMC P/RST are not working. I tried these offsets: 65F1 2 BYTE x 2 MAIN_annunAP[2] Boolean 65F3 1 BYTE MAIN_annunAP_Amber[2] Boolean 65F4 2 BYTE x 2 MAIN_annunAT[2] Boolean 65F6 1 BYTE MAIN_annunAT_Amber[2] Boolean 65F7 2 BYTE x 2 MAIN_annunFMC[2] Boolean FSUIPC Vers 7.3.8 Thanks in advance for your help Rgds Hermann
  12. Here is my solution now: Inputs for MCP I make with OI4FS And some outputs via your new offsets for PMDG Together both work fine! Best regards Hermann
  13. I am unsure if i can use these offsets for Rotary Encoders too??
  14. Hi Paul! Is it possible to have access to Rotary Encoders too? BRgds Hermann
  15. Ok, thanks, I already found these offsets. I can read all (HDG, SPEED, ALTITUDE etc.) but I cannot write to these. I would need to send the values from 4 rotary switches via FSUIPC, because the MCP I own has an USB interface and only the program (SIOC) from OpenCockpit can communicate with it. I have no problem to read other rotary switches via Mobifligt and send it to PMDG 737. But Mobiflight cannot connect to the MCP from OpenCockpit. So I only can connect via FSUIPC. Can I hope in near future, that you can send the missing offsets? Brgds Hermann
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. Guidelines Privacy Policy We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.