Dreamflight767

Hi: I need some help please. I thought I had this figured out but guess not. So...I have: -MFG for rudder -Honeycomb Yoke -Thrustmaster Airbus sidestick None of these are configured in P3D - only FSUIPC In short, I'm trying to get the "twist" of the Thrustmaster to act as tiller except in the Majestic Dash 8 (-8 as I have it labeled) where I need it to act as "spoilers" in order to use it as a tiller per their configurator. But, every time I move the twist of the Thrustmaster, both the rudder and rudder pedals of airplanes move. I can't figure out how to get the twist to stop acting as rudder. It is NOT configured that way in FSUIPC. Thanks. FSUIPC6.ini

Sorry for late reply. Thank you.

This is great. Thanks for the help.

Happy New Year: I need help configuring FSUIPC please. -I have both the Honeycomb Yoke/Bravo Throttle and Thrustmaster Airbus Sidestick and Throttle. -In FSUICP, I have the Honeycomb Yoke X & Y Axis set for aileron/elevator and the honeycomb throttle set for throttle 1 and 2. -Thrustmaster Stidestick and Thrustmaster Throttle are NOT configured in FSUIPC since I'm using the FSLabs input menu. When I load FSLabs airbus, I created a profile in FSUIPC titled "Airbus". I move the Honeycomb Yoke and Throttle and click "Ignore axis" on Axis Assignment and click "OK". However, when I'm back in the cockpit and move honeycomb yoke, the airplane still responds to the Honeycomb movements. In short, I want the Airbus not to respond to the honeycomb yoke and throttle. Thank you!

Hello: For P3Dv5.2, I am not able to delete this entry. It's greyed out and not sure which option it is in the ini. Thanks FSUIPC6.ini

Thanks John. I was kinda hoping that one setting would apply to all aircraft. For example, the "function knob" when I select HDG would allow me to make changes to the heading on the MCP of all airplanes. PMDG, FSLABS, MD-80, Dash 8.

Hello: Is there a tutorial on using FSUIPC to configure the Honeycomb Bravo Throttle? I'm having a difficult time setting the (MCP/Autopilot) buttons. Thanks.

Ok. I'll give that a go. Thanks.

Cool. Thanks!

Hi: I use both Honeycomb Yoke and Thrustmaster Joystick. I've built a profile for FSLabs Airbus but I cannot get FSUIPC to ignore the axis of the X & Y axis of the Honeycomb yoke. -I select "profile" button in the axis tab. -I move the X axis and hit the "ignore" button. -I hit "OK" -I repeat the process for the Y axis. But when I'm back in the cockpit and move the Honeycomb yoke, the flight control of the airplane keeps responding. I want the axis to be ignored but not buttons. Thanks, Aaron Ortega

Sorry to bring up this old topic. But when you say "aircraft name", what does that mean? Airline, Developer, Aircraft Manufacture, Aircraft Model? I guess more specifically, what name of the profile needs to match what name in the sim? In my case, P3Dv5.1. Thanks!

Thank you so much. I was able to follow your advice but had to slightly revise the steps because the ini kept deleting whatever I put the ";" in front of. I'll explain a little later the steps I took incase anyone else needs help.

Hello: I have the Thrustmaster throttle quadrant. Since I fly the PMDG 747 and quadrant only has two thrust handles, I have throttle button #15 set to "Throttle2 Decr" & "Throttle4 Decr" for thrust reverse of engine 2 & 4. However, when I active thrust reverse, only engine #2 goes into reverse. I think it's because there is only 1 option to "Control to repeat..." Any ideas how I get engine #4 to reverse? Thanks, Aaron Ortega

I'll give that a go. Should the slop be positive or negative though?

Hi: The FSUIPC manual says sensitivity should be full right and null zone full left. But doing so, my throttle sensitivity moves considerably. The minute I put my hand on my throttle, airplane throttles move significantly. Any help/tips please. Thanks.

Hi: I need help understanding how to config. FSLabs with FSUIPC: From their manual "FSUIPC SETTINGS Use these recommended settings for null zones if you use FSUIPC to configure your stick axes: Ailerons: 13% of the full movement range number. Elevator: 16% of the full movement range number. Simply take the total axis range number and calculate the percentage mentioned above. Then use that percentage range number and apply it to your null zones. So if your total range number is 16400 for example, 13% of that is 2132. Then use one half of this number for the positive null zone value, and the other half for the negative null zone value" So: -I cannot figure out how to set null zones within FSUIPC. Where is that setting located? -With regards to the last sentence - do they want us to divide 2132 in half and use that number (so 1066?) or do they mean 2132 and -2132? -The manual does not state what values to use for rudder and throttle. I'm using Saitek x52 throttle/control stick and MFG rudder peddles. P3Dv4.5 HF3, most updated ver. of FSLabs and FSUIPC. I've asked on their site but no joy. Thanks.