probleme with flight plan and FMS B737 PMDG

[androl2015]

Hello

Windows 10

MSFS2020

Boeing B737 PMDG

FSUIPC version payware  v7.4.18 

 

 

I've been using Efis and MCP from Opencockpit for a while now, which requires the use of FSUIPC OK it works very well  OK
I've also set up the axes, speed brake... OK
on the other hand, my FMS (CDU from Opencockpit) has been totally disorganized and the aircraft, after entering the flight plan, does not follow the TOC, TOD , ILS etc... settings.
how can I deactivate all the FMC in FSUIPC and I must specify that I haven't set it up at all

sorry i am french and i Translate with DeepL.com (free version)

thankfs for your help

 

Roland

 

Edited November 6 by androl2015

[John Dowson]

1 minute ago, androl2015 said:

FSUIPC version payware  v7.4.18 

First, please check the build date with this version - the first version I initially uploaded was incorrectly built against the MSFS2024 SDK. I later re-released, with the same version number, but with the build date updated. Check your FSUIPC7.log file - if you see this on the 1st line:

Quote

********* FSUIPC7, Version 7.4.18 (1st November 2024) by John Dowson *********

 

then download and re-install. It should be:

Quote

********* FSUIPC7, Version 7.4.18 (3rd November 2024) by John Dowson *********

Otherwise please clarify: was this working in earlier versions, and if so which version were you using?

6 minutes ago, androl2015 said:

on the other hand, my FMS (CDU from Opencockpit) has been totally disorganized and the aircraft, after entering the flight plan, does not follow the TOC, TOD , ILS etc... settings.

This can be very aircraft dependent,, and is nothing to do with FSUIPC...FSUIPC only sends the controls what you have assigned...

8 minutes ago, androl2015 said:

how can I deactivate all the FMC in FSUIPC and I must specify that I haven't set it up at all

Is this controlled by FSUIPC? Please show me / attach your FSUIPC7.log and FSUIPC7.ini files.

John

[androl2015]

 FSUIPC7, Version 7.4.18 (3rd November 2024) by John Dowson *********   

yes is this date 

-------------------------------------------

Otherwise please clarify: was this working in earlier versions, and if so which version were you using?

: FSUIPC7 Installer v0.9.25 for v7.3.17 , with this version it was OK , but I hadn't programmed anything 

-----------------------------------------------------

This can be very aircraft dependent,, and is nothing to do with FSUIPC...FSUIPC only sends the controls what you have assigned...

maybe but during the flight I disconnected FSUIPC and the different steps of the FMS flight plan were followed correctly. everything is back to normal 

------------------------------------------------------------

Is this controlled by FSUIPC?  :

yes only Axes, Speed Brake ...

 

Thank you

 

FSUIPC7.ini FSUIPC7.log

Edited November 6 by androl2015

[John Dowson]

Are you no longer using your JetMax737 throttle or your Alpha Flight controls? If not, you should remove from your ini - I have done this in the attached if you want to use that.

22 hours ago, androl2015 said:

on the other hand, my FMS (CDU from Opencockpit) has been totally disorganized and the aircraft, after entering the flight plan, does not follow the TOC, TOD , ILS etc... settings.
how can I deactivate all the FMC in FSUIPC and I must specify that I haven't set it up at all

FSUIPC cannot see your FMS and is doing nothing with it...

However, it has been reported that sometimes FSUIPC's calibration can affect the PMDG737, although this is usually the climb rate and nothing related to the flight plan.
 Anyway, I have also removed unneeded calbration entries in the attached ini, so you could try that,
If you get the same issue, try switching your assignments to use 'Send to FS as normal axis' rather than 'Send direct to FSUIPC calibration' and remove/reset any and all calibration settings,

You also attached the log file when FSUIPC was srill running, and it ends after 31 seconds and so doesn't show much. Please show me a log file generate when you experience your issue, and ALWAYS exit FSUIPC before attaching files.

John

FSUIPC7.ini

[androl2015]

Hello John,

I did a complete flight with your new .ini file and everything is back to normal.

Yes, I no longer have the Jetmax TQ and Honeycomb Alpha, so your file is ok now.

I'm getting a B737 TQ from Flightsimpm in a few weeks, so I'll have to reprogram FSUIPC, I think. hope all goes well

 

many thanks for your help

 

I would like to take this opportunity to inform you that I asked on your forum for the French documentation of FSUIPC v4 or 5, I know, I did not get a response 

 

Roland

 

Edited November 7 by androl2015

[John Dowson]

12 hours ago, androl2015 said:

I would like to take this opportunity to inform you that I asked on your forum for the French documentation of FSUIPC v4 or 5, I know, I did not get a response 

I didn't see this...and there is no such request in your activity. Anyway, check the Documentation section - there is a french translation for FSUIPC4:

John

[androl2015]

Hello John , 

 

Sorry, I I thought sent a request, but that's not a problem..

.when I click on the link nothing happens for the doc in French and I don't get an alarm from my anti-virus... ?

thanks 

Roland

[John Dowson]

Right-click and select Save as...

But here it is:

FSUIPC460Francais.zip

[androl2015]

Hello John

A big thanks All it’s OK

Roland