hrings

I have tried to sort out but the fault still apply FSUIPC6.ini

Sorry I forgot to tell it is the PMDG 737 NGx and NGXu I am using and only that. The Eventid 70325 is the PMDG Event Id for Parking brakes. so what can I delete and what to rename? I see some double files that can be deleted Henning

I have a button connected via an LeoBodnar board and programmed FSUIPC. Problem is that it shows ok in 5-19 sec then release the parking brake. <i have tried both the event ID's 70325 and 65752. Both do the same. They are programmed only in when button pressed and with 536870912 as it is a momentary switch. I have gone through the .ini page but there is no duplicate to either Event or input (P3,0,C70325,536870912 I also have problems with right eng hydraulic is flipping on of at intervalls and unable to find the falt. I include my .ini file Best Henning Ringsvold henning@ringsvold.no FSUIPC6.ini

Thanks for answer. Flap handle was jittering and it might be FS assignments. I have to clean the control section in FS almost every time I make a full restart of the PC because it is often reloaded some axes or buttons when I do that. Do you have any tips how to avoid reloading when full restart is done HenningR

I have two things: 1. What must you do to update the .INI file when correcting manually in wordpad. Is it enough to save or do you have to restart P3D or complete restart of PC 2. I suddenly got problem with my Flap connection. When calibrating the numbers flicker. They also do that in device page so may be it is dome more. May be the solution is to start from scratch again, but that I don't look forward to. Any tips HenningR

Thanks. Think I got it, but not quite shure. Henning

The ones in green I have put in myself and want to keep. The ones in yellow I want to get rid of. Is it just to delete? I feel that I have better overview of the .ini file when looking as ex. 2 And of course the original heading is !Buttons.B737]

In the FSUIPC INI. file is just to remove the last part. (-custom control: <69681>}- for all posting to have a better watch(overview) of the system Henning Ringsvold

Thanks

Sorry. forget. I am running mostly on P3D v4.5 but occ on 5 Only flying PMDG 737 NGx and NGXu with hardware cockpit. All on win 10 at the moment HenningR

How do you program a switch that has a guard but without any switch to lift the guard. I struggled with such a switch as it did not work until I operated the guard og screen panel then the switch on my hardware was working oh Any tips HenningR

I have just installed P3D V5 and FSUIPC 6.0.13 but I am unable to find the module folder in p3d Is it different in p3d v4.5 and V5.1? HenningR

Sorry about that. I forgot that with the use of Mouse Flag you have to remove the initial setting 0,1,2 so Now it is OK HenningR

FSUIPC 6.0.12 Paid version

Hi. I have problems with the hardware switches on electrical panel. They switch ok to off, but unable to switch them ON (GndPwr, APU Gen, both left and right and Gen 1 and 2) They work ok on the NGX. As long as they are momentary switches I have even tried to manually put in a left single (536870912) without any help. I can see the sw. moving normally on virtual cockpit but it seem like they miss the final touch. If I use switches on virtual panel they work OK Any good tips Henning Ringsvold

Thanks Pete. It was the simulator itself that had put some items in the controls. I did not think of checking that because I had earlier deleted all of it HenningR

I am programming switches via FSUIPC and using Leobodnar card. I have some problems on the overhead of PMDG 737-NGX. When switching on Left Recirc Fan the parking brake starting to alternate on/off all the time. Using Event ID 70504 When switching on the APU Bleed the trim wheel starting to trim Nose UP using 69843 When using both the left and right eng bleed switches every time I switch on the flaps increase 1 notch here using 69842 and 69844 When switching R Pack to High it also start to trim nose up. Any solution what to do

Thanks. I have looked at it and don't understand it. I am totaly blanc when it comes to that sort of programming. Anyone that can help me how to in an easy way

I am not familiar with that. Can anyone show me how to, or find an easyer way to solve the 64 button problems Will it be solved with a 6. upgrade? HenningR

What can be done to use moore than 32 buttons on aboard on FSUIPC. I have the paid vers. 5.155 HenningR

Thanks Pete

How can I put in an comment after the lines in FSUIPC.INI after the inouts in f.inst. in the buttons register. I would like to call the buttons by name after the Event ID. I have tried with different brackets, but after PC restart all the comments are gone. F.inst: Buttons. B737 2=R0,23,C69745 {Custom Control 69745} and I would like [Left Fixed Landing Light] How do I do that and not loosing it again on restart HenningR

One last question Should the letter F in the formula be replaced with either C1003, C1004, C1005

Thanks Pete. I have read the documentation, but yoy know there is'nt all that go straith in the place where it shoul. i di'nt knew that you had to add lines I thought you had to modify the already programed lines in the .ini file. I think I know a little moe now so thanks for your patience HenningR

Is it possible to ask for a more specific action. As you probably see I am a novise in this field. I enclose the inifile and the page of FSUIPC for you to see the button in question here is las I can see line 24 whitch is the MCP LNAV button Is it possible to how to do it. HenningR