Cuantreau

Ok John, will try, thanks a lot

Ok John, for the number (it's 4). For the second part I've added [Auto.PMDG 737-700] 1=PMDGAutoBrake.lua Here are the files including my edited PMDGAutoBrake.lua one Thank you very much PMDGAutoBrake.lua

Hello John, I tried with the PMDGAutoBrake.lua you provided, can't seem to make it to work. This is what I'm doing. Copy the .lua to FSUIPC install folder, edit it by replacing myJoynum with A (which is the letter shown when I press the button I wish to assign in fsuipc with running sim), replace myRtoButton with 30, myOffButton with 31, etc. Then look for the PMDGAutoBrake.lua from Select for FS Control ticked and find it in "control sent when button pressed" section. But the rotary switch I use is not responding to that. What am I doing wrong here? Thx.

Thanks buddy, already tried that way, didn't work for me. I'll try with John's file.

Thank you John, always so helpful man!

adanso, couldn't get them to work, I added to the events .txt file in fsuipc folder, but shouldn't there be an .evt file for that to work in the EventFiles folder? thanks

I don't think they released it yet, I'm afraid.

Thanks man, will check it out.

John, MSFS or PMDG's SDK? Thanks

Yes, same thing for the autobrake, can't map them as i did in p3d.

Thanks a lot Andre, will make it work

Andre, so your fuel levers a axis or a single button for each lever like mine? Didn't get how you did it? Could you elaborate a bit more please, thanks man.

Andre, you're the man !!!!!!!!! Thanks so much man, how did you find this?. Fuel levers where the last buttons that I was missing in my throttle quadrant assignments.

You are welcome man

You are welcome, the idle/cutoff for the start levers was a no go unfortunately. Tried all fuel and mixture MSFS keyboard assignments but none worked, so couldn't assign them to FSUIPC obviously.

This is my throttle quadrant (throttletek with button reversers not axis) config through FSUIPC. Note on the last pic, that's how i configure the button reversers to my liking, what throttle set with -1 on parameters give me is the ability to set reversers and choose whether to leave them and they'll increase to max (81% aporx), or release them as soon as i set them, that keeps them in idle until i vacate the runway, then when i want them off i set the thrust a bit and they retract/close. Hope it helps. Will try your suggestions John and let you know. Thanks a lot.

I could do it the exact same way I did it in p3dv5 and fsx as you said. Had no issues whatsoever to make them work with MSFS and the 737-700.

Hi John , firstly thanks for the quick reply, you and your brother are awesome. Secondly, I have no issues with throttles assignment and calibration through FSUIPC, it's the fuel cutoff and idle lever in the new aircraft and the impossibility to assign them to a button that could trigger them, but that would need an SDK release by PMDG I suppose. Hope you can get it before we do and work to add the off-sets. Thanks again very much!

Hello Pete, Is there a way to assign fuel levers idle/cutoff for the new PMDG 737-700 for MSFS? Or we should wait for an update of your add-on? I'm with latest v 7.3.3 Thanks very much in advance.

I'll try to investigate how to do this John, as I've never done it before. Thanks for your support

Thank you, works like charm! I had to edit, because since overwriting this dll to FSUIPC folder I'm getting almost instant CTD when scenery is loaded in most cases, also at 72% of loading it CTD's. When I replace this new with the original dll, no CTD at all. So conclusion, it worked ones but strangely since that first successful attempt of creating new profile, the sim CTD's almost every load.

Hi John, thanks for your support. What I did is go to Axes Assignments, clicked Profile Specific? box, when it asked if "do you want to apply general assignments to this aircraft", I click No, then I see my profile in the window that appears (my case Ngxu), click on it and finally press OK to close FSUIPC UI. I've always done this procedure with no issues. Hope you can fin the bug, not in a hurry though. Obviously it's easy to fix, as I always backup the .ini file, so I copy the segment of axes that gets deleted and all is good again. Thanks again for your support. Great day Sergio

Hi Pete, I'm a long time customer here. I'm having an issue with FSUIPC v6011, I'm on p3dv5.1 HF1 (5.1.12.26829). When I add a "profile specific" for a new livery of the PMDG 737 NGXu (in this case) I loose all my profile Axes. Before setting new profile my axes look like this: [Axes.NGXu] RangeRepeatRate=10 0=0Y,256 1=0Y,D,-16384,-9362,66080,0 -{ Entering=GEAR_DOWN }- 2=0Y,D,-5982,6528,74183,536870912 -{ Entering=Custom control: <74183> }- 3=0Y,U,8831,16383,66079,0 -{ Entering=GEAR_UP }- 4=1X,256,D,1,0,0,0 -{ DIRECT: Aileron }- 5=1Y,256,D,2,0,0,0 -{ DIRECT: Elevator }- 6=2X,256,D,7,0,0,0 -{ DIRECT: LeftBrake }- 7=2Y,256,D,8,0,0,0 -{ DIRECT: RightBrake }- 8=2R,256,D,3,0,0,0 -{ DIRECT: Rudder }- 9=3X,256,F,66818,0,0,0 -{ TO SIM: STEERING_SET }- 10=5X,256,D,9,0,0,0 -{ DIRECT: Throttle1 }- 11=5Y,256,D,10,0,0,0 -{ DIRECT: Throttle2 }- 12=5Z,256,D,23,0,0,0 -{ DIRECT: Flaps }- 13=5U,256,D,22,0,0,0 -{ DIRECT: Spoilers }- After setting new profile, it erases them like this: [Axes.NGXu] RangeRepeatRate=10 Any help would be appreciated. Thank you in advance Sergio

4.927a did it, thanks a lot Pete!!!!!!!

On the same boat here !!!!