Offset 03c0

[Valeryo]

Hi Pete.
I apologize in advance for my English, because I use Google translator.

I encountered a problem.
I'm trying to get data on the button is pressed by an offset 03c0-03ff.
I see a pressing knobs only one joystick.  All other connected joysticks I can not see. Checked out the full range: 03c0, 03c4, 03c8, etc...
I do not understand what is my mistake ...

[Pete Dowson]

I'm trying to get data on the button is pressed by an offset 03c0-03ff.

I see a pressing knobs only one joystick.  All other connected joysticks I can not see. Checked out the full range: 03c0, 03c4, 03c8, etc...

I do not understand what is my mistake ...

 

You always need to tell me the version number of FSUIPC.

 

Offsets 03C0-03FF only provide the button states of those joysticks being actively scanned by FSUIPC. For FSUIPC to scan a joystick there must be at least one assignment to one of its buttons. FSUIPC does not waste time and resources scanning joysticks not actively used in FSUIPC, which is probably what is happening in your case.

 

Regards

Pete

[Valeryo]

Thanks for a prompt reply!

 

Version 4.921f

 

I connected MJoy16, Saitek Yoke, Saitek pedals.
I see pressing of the MJoy16 buttons. And here pressing of the Saitek Yoke buttons isn't present. Some Saitek Yoke buttons are programmed through FSUIPC.
I use FSInterrogate2std for this purpose.

[Pete Dowson]

Thanks for a prompt reply!

 

Version 4.921f

 

I connected MJoy16, Saitek Yoke, Saitek pedals.

I see pressing of the MJoy16 buttons. And here pressing of the Saitek Yoke buttons isn't present. Some Saitek Yoke buttons are programmed through FSUIPC.

I use FSInterrogate2std for this purpose.

 

What joystick numbers are assigned to those devices? Are you looking in the right offsets? The code to keep those offsets up to date is the same for all 16 joystick numbers -- it isn't likely to be working for some numbers and not others.

 

Perhaps you need to show me the FSUIPC4.INI file.

 

You could also try using FSUIPC's logging. Firdt, in FSUIPC.INI, add "Debug=Please" to the [General] section. Then lod FSX, go to the Logging tab, and check Button logging AND set the "Extras" field to 2. This will log just about everything to do with buttons. You can also monitor the offsets you are interested in on the right-hand side. They'll be type U32 and best to check the 'hex' option, and "Normal log" so that the values appear there.

 

Regards

Pete

[Valeryo]

!1=0[General]
UpdatedByVersion=4900
History=6UJMCSNWBVKVHOBQUWQBW
MouseWheelTrim=No
MouseWheelTrimSpeed=1
JoystickTimeout=20
PollGFTQ6=Yes
BlankDisplays=No
FixControlAccel=No
FixMachSpeedBug=No
VisibilityOptions=No
OneCloudLayer=No
CloudTurbulence=No
CloudIcing=No
GenerateCirrus=No
SuppressCloudTurbulence=No
MaxIce=-4
MinIce=-4
UpperWindGusts=No
SuppressWindTurbulence=No
SuppressWindVariance=No
WindTurbulence=No
TurbulenceRate=1.0,5.0
TurbulenceDivisor=20,20,40,40
SuppressAllGusts=No
MaxSurfaceWind=0
WindLimitLevel=200
WindDiscardLevel=400
WindAjustAltitude=No
WindAjustAltitudeBy=2000
SmoothBySimTime=No
WindSmoothing=Yes
WindSmoothness=2
WindSmoothAirborneOnly=No
PressureSmoothness=0
TemperatureSmoothness=0
DisconnTrimForAP=No
ZeroElevForAPAlt=No
ThrottleSyncAll=No
WhiteMessages=No
ShowPMcontrols=No
SpoilerIncrement=512
MagicBattery=No
RudderSpikeRemoval=No
ElevatorSpikeRemoval=No
AileronSpikeRemoval=No
ReversedElevatorTrim=No
ClockSync=No
ClockSyncMins=5
ClearWeatherDynamics=No
OwnWeatherChanges=No
TimeForSelect=4
LoadFlightMenu=No
LoadPlanMenu=No
PauseAfterCrash=No
BrakeReleaseThreshold=75
SaveDataWithFlights=No
ZapSound=firework
ShortAircraftNameOk=No
UseProfiles=No
TCASid=Flight
TCASrange=40
AxisCalibration=No
DirectAxesToCalibs=No
ShowMultilineWindow=Yes
SuppressSingleline=No
SuppressMultilineFS=No
AxisIntercepts=No
DontResetAxes=No
GetNearestAirports=Yes
WeatherReadFactor=2
WeatherRewriteSeconds=1
CustomWeatherModify=No
SimConnectStallTime=1
LuaRerunDelay=66
Console=No
InitDelayDevicesToo=No
MouseWheelMove=No
DeleteVehiclesForAES=Yes
AutoScanDevices=Yes
EnableMouseLook=No
AxesWrongRange=No
InitDelay=0
OOMcheck=No
LogLua=Yes
DebugLua=Yes
LogAxes=Yes
UseMidMouseBtn=Yes
FSVersionUsed="Microsoft Flight Simulator X",10.0.61637.0
SimConnectUsed=10.0.61259.0

[JoyNames]
AutoAssignLetters=No
G=GVL224-4000-8
R=Saitek Pro Flight Rudder Pedals
Y=Saitek Pro Flight Yoke
M=Outgauge-MCP
2=GVL224-4000-8
2.GUID={6EE0ED20-3AAB-11E3-8001-444553540000}
0=Saitek Pro Flight Rudder Pedals
0.GUID={B2B97980-3930-11E3-8002-444553540000}
1=Saitek Pro Flight Yoke
1.GUID={B2B97980-3930-11E3-8003-444553540000}

[buttons]
ButtonRepeat=20,10
2=PY,19,C65758,0
3=PY,18,C65759,0
8=PY,5,C65655,0
9=PY,4,C65656,0
12=RY,20,C66635,0
13=UY,20,C65967,0
14=RY,21,C66636,0
15=UY,21,C65972,0
17=PY,16,C66298,0
20=PY,17,C66299,0
24=PG,14,Cx06000D0C,x0008
25=PG,23,C66059,0
26=PY,0,C1007,1
27=PG,15,Cx06000D0C,x0001
28=PG,29,C66052,0
29=PG,30,Cx06000D0C,x0002
30=PG,31,Cx06000D0C,x0020
31=PG,7,C66079,0
34=PG,2,Cx02000E02,x0000
35=PG,21,C66224,0
36=PG,20,C66452,0
37=RG,24,C65641,0
38=RG,26,C65643,0
39=RG,25,C65640,0
40=RG,27,C65642,0
41=RG,16,C65645,0
42=RG,18,C65647,0
43=RG,17,C65644,0
44=RG,19,C65646,0
45=PG,28,C66448,0
46=PY,14,C65861,0
47=PG,9,Cx02000E00,x0001
48=PG,10,Cx02000E00,x0002
50=PG,6,C66029,0
51=PG,6,C66072,0
52=PY,15,C65752,0
53=UG,6,C66030,0
54=UG,6,C66073,0
55=PG,11,Cx02000E00,x0003
56=UG,23,C66060,0
57=UG,14,Cx0A000D0C,x0008
58=UG,15,Cx0A000D0C,x0001
59=UG,29,C66053,0
60=UG,30,Cx0A000D0C,x0002
61=UG,31,Cx0A000D0C,x0020
62=UG,7,C66080,0
63=PG,13,Cx02000E00,x0005
65=PG,0,Cx02000E02,x0000
66=PG,4,Cx02000E02,x0002
67=PG,3,Cx02000E02,x0001
68=U3,7,C1038,0
69=P3,7,C1038,0
70=P3,4,C65645,0
71=PG,12,Cx02000E00,x0004
72=PG,22,C66531,0
73=PG,8,Cx02000E00,x0000
75=PY,12,CM4:1,0
76=PY,13,CM4:5,0
77=P64,0,CM3:2,0

[AutoSave]
AutoSaveEnabled=No
Next=1
Interval=60
Files=10
SaveOnGround=No

[GPSout]
GPSoutEnabled=No
Port=COM1
Speed=4800
Interval=2000
PosTo6Decimal=No
SimModeIndicator=No
Sentences=

[GPSout2]
GPSoutEnabled=No
Port=<none set>
Speed=4800
Interval=2000
PosTo6Decimal=No
SimModeIndicator=No
Sentences=

[WideServer]
WideFSenabled=Yes

[sounds]
Path=F:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X\Sound\
Device1=Первичный звуковой драйвер
Device2=Динамики (Realtek High Definition Audio)
Device3=LG TV-3 (NVIDIA High Definition Audio)
Device4=Realtek Digital Output(Optical) (Realtek High Definition Audio)
Device5=Realtek Digital Output (Realtek High Definition Audio)

[Programs]
Run1=READY,HIDE,KILL,D:\Fraps\fraps.exe
Run2=READY,HIDE,KILL,D:\SIOC\sioc.exe
Run3=READY,HIDE,KILL,D:\Program Files (x86)\lekseecon\lekseecon.exe

[Axes]
RangeRepeatRate=10
0=RX,256,D,7,0,0,0
1=RY,256,D,8,0,0,0
2=RR,256,D,3,0,0,0
3=YX,256,D,1,0,0,0
4=YY,256,D,2,0,0,0
5=YZ,256,D,9,0,0,0
6=YR,256,D,22,0,0,0
7=YU,256,D,10,0,0,0
8=YV,256,D,22,0,0,0

[JoystickCalibration]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=0
RudderTrimControl=0
CowlFlaps1Control=0
CowlFlaps2Control=0
CowlFlaps3Control=0
CowlFlaps4Control=0
MaxSteerSpeed=60
LeftBrake=-16380,16380/16
RightBrake=-16380,16380/16
SlopeLeftBrake=10
SlopeRightBrake=10
Aileron=-16380,0,0,16380/8
Spoilers=-16380,16380/24
UseAxisControlsForNRZ=No
SteeringTillerControl=0
Rudder=-16380,-64,0,16380
Throttle1=-16380,-512,512,16380/40
Throttle2=-16380,-512,512,16380/40
MapThr12to34=Yes
Elevator=-16380,-512,512,16380

[Axes.Cessna Skyhawk 172SP Paint3]
0=RX,256,D,7,0,0,0
1=RY,256,D,8,0,0,0
2=RR,256,D,3,0,0,0
3=YX,256,D,1,0,0,0
4=YY,256,D,2,0,0,0
5=YZ,256,D,9,0,0,0
6=YR,256,D,22,0,0,0
7=YU,256,D,10,0,0,0
8=YV,256,D,6,0,0,0

[JoystickCalibration.Boeing 747-400 Paint9]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
UseAxisControlsForNRZ=No
MapThr12to34=Yes
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=0
RudderTrimControl=0
CowlFlaps1Control=0
CowlFlaps2Control=0
CowlFlaps3Control=0
CowlFlaps4Control=0
SteeringTillerControl=0
MaxSteerSpeed=60
Aileron=-16380,-512,512,16380/8
Rudder=-16380,64,512,16380
LeftBrake=-16380,16380/16
SlopeLeftBrake=10
RightBrake=-16380,16380/16
SlopeRightBrake=10
Throttle1=-16380,-512,512,16380/40
Throttle2=-16380,-512,512,16380/40
Spoilers=-16380,16380/24

[Axes.Cessna Grand Caravan]
0=RX,256,D,7,0,0,0
1=RY,256,D,8,0,0,0
2=RR,256,D,3,0,0,0
3=YX,256,D,1,0,0,0
4=YY,256,D,2,0,0,0
5=YZ,256,D,4,0,0,0
6=YR,256,D,22,0,0,0
7=YU,256,D,5,0,0,0
8=YV,256,D,6,0,0,0

[buttons.Level D Simulations B767-300ER - United Airlines (Old Livery) - 000]
ButtonRepeat=20,10
10=PG,10,Cx06000356,x0004
11=PG,9,Cx06000356,x0002
30=PG,24,CM2:2,0
31=PG,26,CM2:1,0
32=PG,25,CM2:3,0
33=PG,27,CM2:4,0
34=PG,28,CM2:5,0
35=PG,12,Cx06000356,x0010
36=PG,11,Cx06000356,x0008
1=PG,29,Cx06000D0C,x0010
2=PG,15,Cx06000D0C,x0001
37=PG,7,C66079,0
39=PG,31,Cx06000D0C,x0020
40=PG,30,Cx06000D0C,x0002
41=PG,14,Cx06000D0C,x0008
42=PG,23,Cx06000D0C,x0004
43=RY,14,Cx0200080C,x0001
44=UY,14,Cx0200080C,x0000
45=PG,8,Cx06000356,x0001
46=PG,2,Cx06000352,x0004
47=RG,16,CM1:1,0
48=RG,18,CM1:3,0
49=RG,17,CM1:2,0
50=RG,19,CM1:4,0
52=RG,21,Cx06000371,x0020
54=UG,21,Cx0A000371,x0020
55=PG,22,C66531,0
57=UG,23,Cx0A000D0C,x0004
58=UG,14,Cx0A000D0C,x0008
59=UG,15,Cx0A000D0C,x0001
60=UG,29,Cx0A000D0C,x0010
61=UG,30,Cx0A000D0C,x0002
62=UG,31,Cx0A000D0C,x0020
63=UG,7,C66080,0
64=UG,8,Cx0A000356,x0001
65=UG,9,Cx0A000356,x0002
66=UG,10,Cx0A000356,x0004
67=UG,11,Cx0A000356,x0008
68=UG,12,Cx0A000356,x0010
70=PG,13,Cx06000356,x0020
71=UG,13,Cx0A000356,x0020
72=PG,0,Cx06000352,x0001
73=UG,0,Cx0A000352,x0001
74=PG,1,Cx06000352,x0002
75=UG,1,Cx0A000352,x0002
76=UG,2,Cx0A000352,x0004
77=PG,3,Cx06000352,x0008
78=UG,3,Cx0A000352,x0008
79=PG,4,Cx06000352,x0010
80=UG,4,Cx0A000352,x0010
81=PG,5,Cx06000352,x0020
82=UG,5,Cx0A000352,x0020
83=PG,20,CM1:5,0
84=PG,6,CM1:6,0
85=UG,6,CM1:6,0

[Axes.C Skylane 182Q2]
0=YX,256,D,1,0,0,0
1=YY,256,D,2,0,0,0
2=YZ,256,D,9,0,0,0
3=YR,256,D,22,0,0,0
4=YU,256,D,5,0,0,0
5=YV,256,D,6,0,0,0
6=RX,256,D,7,0,0,0
7=RY,256,D,8,0,0,0
8=RR,256,D,3,0,0,0

[Axes.Piper Cub]
0=YX,256,D,1,0,0,0
1=YY,256,D,2,0,0,0
2=YZ,256,D,9,0,0,0
3=YR,256,D,22,0,0,0
4=YU,256,D,10,0,0,0
5=YV,256,D,6,0,0,0
6=RX,256,D,7,0,0,0
7=RY,256,D,8,0,0,0
8=RR,256,D,3,0,0,0

[Axes.C172 Anniversary]
0=YX,256,D,1,0,0,0
1=YY,256,D,2,0,0,0
2=YZ,256,D,9,0,0,0
3=YR,256,D,22,0,0,0
4=YU,256,D,10,0,0,0
5=YV,256,D,6,0,0,0
6=RX,256,D,7,0,0,0
7=RY,256,D,8,0,0,0
8=RR,256,D,3,0,0,0

[Axes.Carenado B200 King 2]
0=YX,256,D,1,0,0,0
1=YY,256,D,2,0,0,0
2=YZ,256,D,4,0,0,0
3=YR,256,D,22,0,0,0
4=YU,256,D,5,0,0,0
5=YV,256,D,6,0,0,0
6=RX,256,D,7,0,0,0
7=RY,256,D,8,0,0,0
8=RR,256,D,3,0,0,0

[buttons.Carenado B200 King Air 6]
0=RY,20,C66634,0
1=UY,20,C65604,0
2=PY,14,C65793,0
3=PY,16,C66297,0

[Axes.Carenado B200 King Air 6]
0=YX,256,D,1,0,0,0
1=YY,256,D,2,0,0,0
2=YZ,256,D,4,0,0,0
3=YR,256,D,22,0,0,0
4=YU,256,D,5,0,0,0
5=YV,256,D,6,0,0,0
6=RX,256,D,7,0,0,0
7=RY,256,D,8,0,0,0
8=RR,256,D,3,0,0,0

[JoystickCalibration.Carenado B200 King Air 6]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
UseAxisControlsForNRZ=No
MapThr12to34=Yes
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=0
RudderTrimControl=0
CowlFlaps1Control=0
CowlFlaps2Control=0
CowlFlaps3Control=0
CowlFlaps4Control=0
SteeringTillerControl=0
MaxSteerSpeed=60
Aileron=-16380,512,524,16380/8
Elevator=-16380,-512,512,16380
Rudder=-16380,-64,0,16380
LeftBrake=-16380,16380/16
SlopeLeftBrake=10
RightBrake=-16380,16380/16
SlopeRightBrake=10
Throttle1=-16380,-512,512,16380/40
Throttle2=-16380,-512,512,16380/40
Spoilers=-16380,16380/24
SlopeAileron=3
SlopeElevator=2

[JoystickCalibration.Level D Simulations B767-300ER - United Airlines (Old Livery) - 000]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
UseAxisControlsForNRZ=No
MapThr12to34=Yes
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=0
RudderTrimControl=0
CowlFlaps1Control=0
CowlFlaps2Control=0
CowlFlaps3Control=0
CowlFlaps4Control=0
SteeringTillerControl=0
MaxSteerSpeed=60
Aileron=-16380,-969,493,16380/8
SlopeAileron=8
Elevator=-16380,-512,512,16380
SlopeElevator=4
Rudder=-16380,-64,0,16380
LeftBrake=-16380,16380/16
SlopeLeftBrake=10
RightBrake=-16380,16380/16
SlopeRightBrake=10
Throttle1=-16380,-512,512,16380/40
Throttle2=-16380,-512,512,16380/40
Spoilers=-16380,16380/24

[JoystickCalibration.Learjet 45 FP]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
UseAxisControlsForNRZ=No
MapThr12to34=Yes
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=0
RudderTrimControl=0
CowlFlaps1Control=0
CowlFlaps2Control=0
CowlFlaps3Control=0
CowlFlaps4Control=0
SteeringTillerControl=0
MaxSteerSpeed=60
Aileron=-16380,-969,493,16380/8
Elevator=-16380,-512,512,16380/8
Rudder=-16380,-64,0,16380
LeftBrake=-16380,16380/16
SlopeLeftBrake=10
RightBrake=-16380,16380/16
SlopeRightBrake=10
Throttle1=-16384,-16384,-16384,16383/40
Throttle2=-16384,-16384,-16384,16254/40
Spoilers=-16380,16380/24
SlopeAileron=1
SlopeElevator=7

[JoystickCalibration.Boeing 737-800 Paint2]
AllowSuppressForPFCquad=Yes
ExcludeThrottleSet=Yes
ExcludeMixtureSet=Yes
ExcludePropPitchSet=Yes
SepRevsJetsOnly=No
ApplyHeloTrim=No
UseAxisControlsForNRZ=No
MapThr12to34=Yes
FlapsSetControl=0
FlapDetents=No
ReverserControl=66292
Reverser1Control=66422
Reverser2Control=66425
Reverser3Control=66428
Reverser4Control=66431
MaxThrottleForReverser=256
AileronTrimControl=0
RudderTrimControl=0
CowlFlaps1Control=0
CowlFlaps2Control=0
CowlFlaps3Control=0
CowlFlaps4Control=0
SteeringTillerControl=0
MaxSteerSpeed=60
Aileron=-16191,-1988,-128,16383/8
Elevator=-16380,-512,512,16380
Rudder=-16380,-64,0,16380
LeftBrake=-16380,16380/16
SlopeLeftBrake=10
RightBrake=-16380,16380/16
SlopeRightBrake=10
Throttle1=-16380,-512,512,16380/40
Throttle2=-16380,-512,512,16380/40
Spoilers=-16380,16380/24

[General]
UpdatedByVersion=4921f
History=IZH9RYBWYJK32OQ0R2VGT
InitDelayDevicesToo=No
UseMidMouseBtn=Yes
MouseWheelMove=No
MouseWheelTrim=No
MouseWheelTrimSpeed=1
JoystickTimeout=20
PollGFTQ6=Yes
BlankDisplays=No
FixControlAccel=No
FixMachSpeedBug=No
DeleteVehiclesForAES=Yes
AutoScanDevices=Yes
VisibilityOptions=No
OneCloudLayer=No
CloudTurbulence=No
CloudIcing=No
GenerateCirrus=No
SuppressCloudTurbulence=No
MaxIce=-4
MinIce=-4
UpperWindGusts=No
SuppressWindTurbulence=No
SuppressWindVariance=No
WindTurbulence=No
TurbulenceRate=1.0,5.0
TurbulenceDivisor=20,20,40,40
SuppressAllGusts=No
MaxSurfaceWind=0
WindLimitLevel=200
WindDiscardLevel=400
WindAjustAltitude=No
WindAjustAltitudeBy=2000
SmoothBySimTime=No
WindSmoothing=No
WindSmoothness=2
WindSmoothAirborneOnly=Yes
PressureSmoothness=0
TemperatureSmoothness=0
DisconnTrimForAP=No
ZeroElevForAPAlt=No
ThrottleSyncAll=No
WhiteMessages=No
ShowPMcontrols=No
SpoilerIncrement=512
MagicBattery=No
RudderSpikeRemoval=No
ElevatorSpikeRemoval=No
AileronSpikeRemoval=No
ReversedElevatorTrim=No
ClockSync=No
ClockSyncMins=5
ClearWeatherDynamics=No
OwnWeatherChanges=No
TimeForSelect=4
LoadFlightMenu=No
LoadPlanMenu=No
PauseAfterCrash=Yes
BrakeReleaseThreshold=75
SaveDataWithFlights=No
ZapSound=firework
ShortAircraftNameOk=Substring
UseProfiles=Yes
EnableMouseLook=No
AxesWrongRange=No
TCASid=Flight
TCASrange=40
AxisCalibration=No
DirectAxesToCalibs=No
ShowMultilineWindow=Yes
SuppressSingleline=No
SuppressMultilineFS=No
AxisIntercepts=No
DontResetAxes=No
InitDelay=0
GetNearestAirports=Yes
OOMcheck=Yes
WeatherReadFactor=2
WeatherRewriteSeconds=1
CustomWeatherModify=No
SimConnectStallTime=1
LuaRerunDelay=66
Console=No
UseSystemTime=No
FSVersionUsed="Microsoft Flight Simulator X",10.0.61637.0
SimConnectUsed=10.0.61259.0

[Profile.Cessna Skyhawk 172SP Paint3]
1=Cessna Skyhawk 172SP Paint3

[Profile.Beech King Air 350 Paint3]
1=Beech King Air 350 Paint3

[Profile.Boeing 747-400 Paint9]
1=Boeing 747-400 Paint9

[Profile.Cessna Grand Caravan]
1=Cessna Grand Caravan

[Profile.Boeing 747-400 Paint8]
1=Boeing 747-400 Paint8

[Profile.Boeing 747-400 Paint2]
1=Boeing 747-400 Paint2

[Profile.Level D Simulations B767-300ER - United Airlines (Old Livery) - 000]
1=Level D Simulations B767-300ER - United Airlines (Old Livery) - 000
2=Level D Simulations B767-300ER - Nordwind Airlines - 000

[Profile.C Skylane 182Q2]
1=C Skylane 182Q2

[Profile.Cessna 208 Caravan Amphibian Paint2]
1=Cessna 208 Caravan Amphibian Paint2

[Profile.Level D Simulations B767-300ER - KLM Royal Dutch Airlines - 000]
1=Level D Simulations B767-300ER - KLM Royal Dutch Airlines - 000

[Profile.Piper Cub]
1=Piper Cub

[Profile.C172 Anniversary]
1=C172 Anniversary

[Profile.Carenado B200 King Air 6]
1=Carenado B200 King Air 6

[Profile.Learjet 45 FP]
1=Learjet 45 FP
2=Learjet 45

[Profile.Boeing 737-800 Paint2]
1=Boeing 737-800 Paint2

[MacroFiles]
1=767
2=45
3=md80

[buttons.Learjet 45 FP]
ButtonRepeat=2,10
2=PY,19,C65758,0
3=PY,18,C65759,0
8=PY,5,C65655,0
9=PY,4,C65656,0
12=RY,20,C66635,0
13=UY,20,C65967,0
14=RY,21,C66636,0
15=UY,21,C65972,0
17=PY,16,C66298,0
20=PY,17,C66299,0
24=PG,14,Cx06000D0C,x0008
25=PG,23,C66059,0
26=PY,0,C1007,1
27=PG,15,Cx06000D0C,x0001
28=PG,29,C66052,0
29=PG,30,Cx06000D0C,x0002
30=PG,31,Cx06000D0C,x0020
31=PG,7,C66079,0
35=PG,21,C66224,0
36=PG,20,C66452,0
37=RG,24,C65641,0
38=RG,26,C65643,0
39=RG,25,C65640,0
40=RG,27,C65642,0
41=RG,16,C65645,0
42=RG,18,C65647,0
43=RG,17,C65644,0
44=RG,19,C65646,0
45=PG,28,C66448,0
46=PY,14,C65861,0
50=PG,6,C66029,0
51=PG,6,C66072,0
52=PY,15,C65752,0
53=UG,6,C66030,0
54=UG,6,C66073,0
56=UG,23,C66060,0
57=UG,14,Cx0A000D0C,x0008
58=UG,15,Cx0A000D0C,x0001
59=UG,29,C66053,0
60=UG,30,Cx0A000D0C,x0002
61=UG,31,Cx0A000D0C,x0020
62=UG,7,C66080,0
66=PG,4,CM2:1,0
79=PG,10,CM2:3,0
80=PG,12,CM2:2,0
81=PG,5,CM2:1,0
82=PG,3,CM2:1,0
83=PG,2,CM2:1,0
84=PG,1,CM2:1,0
85=PG,0,CM2:1,0
86=PG,22,C66531,0

[Profile.Carenado B200 King 2]
1=Carenado B200 King 2
 

[Valeryo]

 AND set the "Extras" field to 2. 

 

I didn't find such field.

[Pete Dowson]

...

 

 

Well, I only really needed to see theButtons and Joynames sections. I didn't realise it was so long!

 

One of the reasons it is long, you have a large section at the beginning which is commented out and so unused. It's a spare [General] section. Don't know what happened there -- the only operating one is later on. So to clarify things for you, please first delete all the first section, from

 

!1=0[General]

 

down to

SimConnectUsed=10.0.61259.0

 

inclusive. Looks like that was the [general] section when you used version 4.90.

 

Next, the JoyNames section shows these devices:given letters:

 

R=Saitek Pro Flight Rudder Pedals

Y=Saitek Pro Flight Yoke

G=GVL224-4000-8

M=Outgauge-MCP

 

but of those 4, only 3 are connected:

 

0=Saitek Pro Flight Rudder Pedals

1=Saitek Pro Flight Yoke

2=GVL224-4000-8

 

I assume the MCP one is device 3? Because you have some device 3 assignments which have not been replaced by letters (yet): Maybe this is historical and needs tidying up?

 

68=U3,7,C1038,0

69=P3,7,C1038,0

70=P3,4,C65645,0

 

In the default [buttons] section you have assignments to Y and G, so certainly both of those should be registering the button states -- Y in 03C4 and G in 03C8.

 

Now, you said:

 

I connected MJoy16, Saitek Yoke, Saitek pedals.

I see pressing of the MJoy16 buttons. And here pressing of the Saitek Yoke buttons isn't present. Some Saitek Yoke buttons are programmed through FSUIPC.

 

 

but unless by "MJoy16" you mean "GVL224-4000-8", the MJoy16 device is not connected -- or at least it was not when you posted this INI file. So I think you may be getting confused over the offsets you are looking at. If, when connected, the MJoy16 is joystick #3, then its buttons will be at offset 03CC. But you also need to then check that the assignments to #3 are being changed to 'M', the letter assigned for 3. I honestly don't know how you got the '3's left in the file -- there are no assignments shown at all for 'M' so it won't be scanned even if connected, UNLESS it is actually 3 and the assignment lines get changed.

 

Regards

Pete

[Valeryo]

It seems I understood.

 

Here fragment

 

 

517424 Button changed: bRef=0, Joy=1 (Y), Btn=4, Pressed
517424 [buttons.Learjet 45 FP] 9=PY,4,C65656,0
517424 [DNSCAN] J0.1, B4, bRes=2, Flags=X01, Value=65656[0x10078], Param=0[0x0], TimeNow=3465624, TimeLast=3438511
517424 FS Control Sent: Ctrl=65656, Param=0
517596 Button changed: bRef=0, Joy=1 (Y), Btn=4, Released
549498 Button changed: bRef=0, Joy=2 (G), Btn=23, Pressed
549498 [buttons.Learjet 45 FP] 25=PG,23,C66059,0
549498 [DNSCAN] J0.2, B23, bRes=2, Flags=X01, Value=66059[0x1020B], Param=0[0x0], TimeNow=3497698, TimeLast=3465624
549498 FS Control Sent: Ctrl=66059, Param=0
549966 Button changed: bRef=0, Joy=2 (G), Btn=23, Released
549966 [buttons.Learjet 45 FP] 56=UG,23,C66060,0
549966 [uPSCAN:] J0.2, B23, bRes=1, Flags=X03, Value=66060[0x1020C], Param=0[0x0], TimeNow=3498166, TimeLast=3497698
549966 FS Control Sent: Ctrl=66060, Param=0
552946 Button changed: bRef=0, Joy=1 (Y), Btn=4, Pressed
552946 [buttons.Learjet 45 FP] 9=PY,4,C65656,0
552946 [DNSCAN] J0.1, B4, bRes=2, Flags=X01, Value=65656[0x10078], Param=0[0x0], TimeNow=3501146, TimeLast=3498166
552946 FS Control Sent: Ctrl=65656, Param=0
553117 Button changed: bRef=0, Joy=1 (Y), Btn=4, Released
554350 Button changed: bRef=0, Joy=1 (Y), Btn=5, Pressed
554350 [buttons.Learjet 45 FP] 8=PY,5,C65655,0
554350 [DNSCAN] J0.1, B5, bRes=2, Flags=X01, Value=65655[0x10077], Param=0[0x0], TimeNow=3502550, TimeLast=3501146
554350 FS Control Sent: Ctrl=65655, Param=0
554459 Button changed: bRef=0, Joy=1 (Y), Btn=5, Released
559607 Button changed: bRef=0, Joy=1 (Y), Btn=19, Pressed
559607 [buttons.Learjet 45 FP] 2=PY,19,C65758,0
559607 [DNSCAN] J0.1, B19, bRes=2, Flags=X01, Value=65758[0x100DE], Param=0[0x0], TimeNow=3507807, TimeLast=3502550
559607 FS Control Sent: Ctrl=65758, Param=0
559716 Button changed: bRef=0, Joy=1 (Y), Btn=19, Released
561214 Button changed: bRef=0, Joy=1 (Y), Btn=18, Pressed
561214 [buttons.Learjet 45 FP] 3=PY,18,C65759,0
561214 [DNSCAN] J0.1, B18, bRes=2, Flags=X01, Value=65759[0x100DF], Param=0[0x0], TimeNow=3509414, TimeLast=3507807
561214 FS Control Sent: Ctrl=65759, Param=0
561354 Button changed: bRef=0, Joy=1 (Y), Btn=18, Released
597343 Sim stopped: average frame rate for last 143 secs = 29.9 fps

[Pete Dowson]

It seems I understood.

 

Where's the monitoring of offsets 03C4 and 03C8?

 

Also I see only one action on Device G, with one button pressed for less than 500 mSecs. That should be enough to detect the change in 03C8, though, so let's see the Monitoring.

 

549498 Button changed: bRef=0, Joy=2 (G), Btn=23, Pressed

549966 Button changed: bRef=0, Joy=2 (G), Btn=23, Released

 

As I said, FSUIPC does not (cannot) distinguish between joysticks as far as changing the 03C0-- range of offsets. The joystick number simply acts as an index for storing the 32 bit word it gets from Windows. It is very straightforward indeed.

 

Regards

Pete

 

[Valeryo]

Well, I only really needed to see theButtons and Joynames sections. I didn't realise it was so long!

 

One of the reasons it is long, you have a large section at the beginning which is commented out and so unused. It's a spare [General] section. Don't know what happened there -- the only operating one is later on. So to clarify things for you, please first delete all the first section, from

 

!1=0[General]

 

down to

SimConnectUsed=10.0.61259.0

 

inclusive. Looks like that was the [general] section when you used version 4.90.

 

Next, the JoyNames section shows these devices:given letters:

 

R=Saitek Pro Flight Rudder Pedals

Y=Saitek Pro Flight Yoke

G=GVL224-4000-8

M=Outgauge-MCP

 

but of those 4, only 3 are connected:

 

0=Saitek Pro Flight Rudder Pedals

1=Saitek Pro Flight Yoke

2=GVL224-4000-8

 

I assume the MCP one is device 3? Because you have some device 3 assignments which have not been replaced by letters (yet): Maybe this is historical and needs tidying up?

 

 

 

Yes, you are right.

[Valeryo]

Where's the monitoring of offsets 03C4 and 03C8?

 

How it can be done?

[Valeryo]

"MJoy16" you mean "GVL224-4000-8", the MJoy16 device is not connected -- or at least it was not when you posted this INI file. 

 

GVL224-4000-8 it is modified MJoy16. Sorry.

[Pete Dowson]

How it can be done?

 

You missed that? When I asked you to turn on extra logging, I said, in referring to the Logging tab:

 

You can also monitor the offsets you are interested in on the right-hand side. They'll be type U32 and best to check the 'hex' option, and "Normal log" so that the values appear there.

 

You will also find it clearly documented in the FSUIPC Advanced User's guide, though they are pretty easy to understand when you look at the Logging tab.

 

Pete

[Valeryo]

So?

     

[Pete Dowson]

So?

     

 

 

What's the picture for? Why have you checked "DebugString"? Do you have a debugger running in which to receive those? Use the "Normal Log" check box as I said.  You don't seem to read what I write, or at least not enough of it, and it gets a bit tiresome having to repeat myself. Please pay attention.

 

Regards

Pete

[Valeryo]

I see an essence from it doesn't change.
I connected Saitek Yoke and GVL224-4000-8 (analog Mjoy16). I programmed buttons through FSUIPC.
All this well works.
However.
I can see pressing of buttons only at one device - GVL224-4000-8. Offset 03c0.

I don't see pressing of the Saitek Yoke buttons on one of other offsets: 03c4, 03c8, 03cc, 03d0, 03d4, 03d8, 03dc................ 03fc.

Why?

[Pete Dowson]

I see an essence from it doesn't change.

I connected Saitek Yoke and GVL224-4000-8 (analog Mjoy16). I programmed buttons through FSUIPC.

All this well works.

However.

I can see pressing of buttons only at one device - GVL224-4000-8. Offset 03c0.

I don't see pressing of the Saitek Yoke buttons on one of other offsets: 03c4, 03c8, 03cc, 03d0, 03d4, 03d8, 03dc................ 03fc.

Why?

 

Sorry, we are back at the very start! What on Earth are you doing? What happened to all the interaction till now?

 

The whole purpose of me asking you to log things was to enable me to see what is happening. So far you have not done as I asked and I am none the wiser. Why can't you folllow simple instructions?

 

I am not going to be able to help you unless you do as I ask!!! What's the point of me asking you to do these things if you then don't bother or do them entirely incorrectly? I've got better things to do than this which is turning out to be an immense waste of time and effort!

 

:-(

 

Pete

[Pete Dowson]

The whole purpose of me asking you to log things was to enable me to see what is happening

 

 

BTW there is a good reason I need the exact data, to see exactly what is occurring. I don't have more than one normal "joystick" type device -- all my main controls are PFC serial port devices, and these offsets do not apply to those. I only have one joystick type device, and of course that is device #0 and 03C0 responds correctly to its buttons.

 

I'll look through the code and see if there's something I have wrong, but actual log data would be of immense help. PLEASE!

 

If i do find anything to change I will be asking you to test it for me. The code in this area is quite old and mostly ported from the FS9 version of FSUIPC.

 

Oh, one other thing. I noticed in your previous log that you press several buttons on both devices quite close Please press one button on each device and leave a few seconds between each press, then show me the log.

 

Pete

[Valeryo]

I made everything as you told me.
There are difficulties of a language barrier. And my personal curiosity.

[Pete Dowson]

I made everything as you told me.

There are difficulties of a language barrier. And my personal curiosity.

 

You made everything? So why not show me the log which resulted? Why keep it to yourself?

 

I am trying to help, and I'm sorry that I only write English, but perhaps you could read it more carefully, and at least ask questions if you need me to elaborate?

 

I am worried that there is a bug in FSUIPC. If there is one it has been there for many years. I just need more information, as I cannot test it here without going out and buying another joystick or three.

 

Please set the logging as I asked, then press one button on each device, waiting two-three seconds between each. THEN paste the log into a message here.

 

Thank you!

 

Pete

[Valeryo]

I with pleasure will help!

 

 

********* FSUIPC4, Version 4.921f by Pete Dowson *********
Running inside FSX on Windows 7
Module base=5D710000
User Name="Valery Omelchenko"
User Addr="omelchenkovu@mail.ru"
FSUIPC4 Key is provided
WIDEFS7 not user registered, or expired
234 System time = 01/11/2013 23:28:14
234 FLT path = "C:\Users\Valery\Documents\Файлы Flight Simulator X\"
265 Trying to connect to SimConnect Acc/SP2 Oct07 ...
296 FS path = "F:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X\"
608 LogOptions=40000000 00000031
608 SIM1 Frictions access gained
608 Wind smoothing fix is fully installed
608 G3D.DLL fix attempt installed ok
608 SimConnect_Open succeeded: waiting to check version okay
608 Trying to use SimConnect Acc/SP2 Oct07
1966 Ready Flags: Ready-To-Fly=N, In Menu=N, In Dlg=N
1981 Running in "Microsoft Flight Simulator X", Version: 10.0.61637.0 (SimConnect: 10.0.61259.0)
1981 Initialising SimConnect data requests now
1981 FSUIPC Menu entry added
2028 Ready Flags: Ready-To-Fly=N, In Menu=Y, In Dlg=Y
2028 C:\Users\Valery\Documents\Файлы Flight Simulator X\UIII.FLT
2028 F:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X\SimObjects\Airplanes\Lear45\Lear45.AIR
2106 AppKey="7A2958KP9QAX"
2168 Memory in use: 483Mb, Avail=3613Mb
2200 Monitor IPC:03C0 (U32) = 0x0
2200 Monitor IPC:03C4 (U32) = 0x0
2200 Monitor IPC:03C8 (U32) = 0x0
2200 Monitor IPC:03CC (U32) = 0x0
23697 Ready Flags: Ready-To-Fly=N, In Menu=N, In Dlg=N
24133 Ready Flags: Ready-To-Fly=N, In Menu=Y, In Dlg=Y
48204 System time = 01/11/2013 23:29:02, Simulator time = 23:28:16 (17:28Z)
48282 Aircraft="Learjet 45 FP"
48282 [buttons] now profile-specific:
48282 3=PY,18,C65759,0
48282 8=PY,5,C65655,0
48282 9=PY,4,C65656,0
48282 12=RY,20,C66635,0
48282 12=RY,20,C66635,0
48282 14=RY,21,C66636,0
48282 14=RY,21,C66636,0
48282 17=PY,16,C66298,0
48282 20=PY,17,C66299,0
48282 24=PG,14,Cx06000D0C,x0008
48282 24=PG,14,Cx06000D0C,x0008
48282 25=PG,23,C66059,0
48282 25=PG,23,C66059,0
48282 26=PY,0,C1007,1
48282 27=PG,15,Cx06000D0C,x0001
48282 27=PG,15,Cx06000D0C,x0001
48282 28=PG,29,C66052,0
48282 28=PG,29,C66052,0
48282 29=PG,30,Cx06000D0C,x0002
48282 29=PG,30,Cx06000D0C,x0002
48282 30=PG,31,Cx06000D0C,x0020
48282 30=PG,31,Cx06000D0C,x0020
48282 31=PG,7,C66079,0
48282 31=PG,7,C66079,0
48282 35=PG,21,C66224,0
48282 36=PG,20,C66452,0
48282 37=RG,24,C65641,0
48282 38=RG,26,C65643,0
48282 39=RG,25,C65640,0
48282 40=RG,27,C65642,0
48282 41=RG,16,C65645,0
48282 42=RG,18,C65647,0
48282 43=RG,17,C65644,0
48282 44=RG,19,C65646,0
48282 45=PG,28,C66448,0
48282 46=PY,14,C65861,0
48282 50=PG,6,C66029,0
48282 50=PG,6,C66029,0
48282 50=PG,6,C66029,0
48282 50=PG,6,C66029,0
48282 52=PY,15,C65752,0
48282 66=PG,4,CM2:1,0
48282 79=PG,10,CM2:3,0
48282 80=PG,12,CM2:2,0
48282 82=PG,3,CM2:1,0
48282 83=PG,2,CM2:1,0
48282 85=PG,0,CM2:1,0
48282 86=PG,22,C66531,0
48282 [buttons] now profile-specific:
48282 2=PY,19,C65758,0
48282 3=PY,18,C65759,0
48282 8=PY,5,C65655,0
48282 9=PY,4,C65656,0
48282 12=RY,20,C66635,0
48282 12=RY,20,C66635,0
48282 14=RY,21,C66636,0
48282 14=RY,21,C66636,0
48282 17=PY,16,C66298,0
48282 20=PY,17,C66299,0
48282 24=PG,14,Cx06000D0C,x0008
48282 24=PG,14,Cx06000D0C,x0008
48282 25=PG,23,C66059,0
48282 25=PG,23,C66059,0
48282 26=PY,0,C1007,1
48298 27=PG,15,Cx06000D0C,x0001
48298 27=PG,15,Cx06000D0C,x0001
48298 28=PG,29,C66052,0
48298 28=PG,29,C66052,0
48298 29=PG,30,Cx06000D0C,x0002
48298 29=PG,30,Cx06000D0C,x0002
48298 30=PG,31,Cx06000D0C,x0020
48298 30=PG,31,Cx06000D0C,x0020
48298 31=PG,7,C66079,0
48298 31=PG,7,C66079,0
48298 35=PG,21,C66224,0
48298 36=PG,20,C66452,0
48298 37=RG,24,C65641,0
48298 38=RG,26,C65643,0
48298 39=RG,25,C65640,0
48298 40=RG,27,C65642,0
48298 41=RG,16,C65645,0
48298 42=RG,18,C65647,0
48298 43=RG,17,C65644,0
48298 44=RG,19,C65646,0
48298 45=PG,28,C66448,0
48298 46=PY,14,C65861,0
48298 50=PG,6,C66029,0
48298 50=PG,6,C66029,0
48298 50=PG,6,C66029,0
48298 50=PG,6,C66029,0
48298 52=PY,15,C65752,0
48298 66=PG,4,CM2:1,0
48298 79=PG,10,CM2:3,0
48298 80=PG,12,CM2:2,0
48298 82=PG,3,CM2:1,0
48298 83=PG,2,CM2:1,0
48298 85=PG,0,CM2:1,0
48298 86=PG,22,C66531,0
49655 Ready Flags: Ready-To-Fly=N, In Menu=N, In Dlg=N
54585 Starting everything now ...
54616 Ready Flags: Ready-To-Fly=Y, In Menu=N, In Dlg=N
54632 Run: "D:\Fraps\fraps.exe"
54632 Run: "D:\SIOC\sioc.exe"
54632 Run: "D:\Program Files (x86)\lekseecon\lekseecon.exe"
54803 AppKey="7A2958KP9QAX"
55911 Advanced Weather Interface Enabled
62369 Memory in use: 1164Mb, Avail=2932Mb
74849 Ready Flags: Ready-To-Fly=Y, In Menu=Y, In Dlg=Y
74849 Sim stopped: average frame rate for last 25 secs = 28.4 fps
92821 LogOptions changed, now 40000000 00000021
92821 [buttons] now profile-specific:
92821 2=PY,19,C65758,0
92821 3=PY,18,C65759,0
92821 8=PY,5,C65655,0
92821 9=PY,4,C65656,0
92821 12=RY,20,C66635,0
92821 12=RY,20,C66635,0
92821 14=RY,21,C66636,0
92821 14=RY,21,C66636,0
92821 17=PY,16,C66298,0
92821 20=PY,17,C66299,0
92821 24=PG,14,Cx06000D0C,x0008
92821 24=PG,14,Cx06000D0C,x0008
92821 25=PG,23,C66059,0
92821 25=PG,23,C66059,0
92821 26=PY,0,C1007,1
92821 27=PG,15,Cx06000D0C,x0001
92821 27=PG,15,Cx06000D0C,x0001
92821 28=PG,29,C66052,0
92821 28=PG,29,C66052,0
92821 29=PG,30,Cx06000D0C,x0002
92821 29=PG,30,Cx06000D0C,x0002
92821 30=PG,31,Cx06000D0C,x0020
92821 30=PG,31,Cx06000D0C,x0020
92821 31=PG,7,C66079,0
92821 31=PG,7,C66079,0
92821 35=PG,21,C66224,0
92821 36=PG,20,C66452,0
92821 37=RG,24,C65641,0
92821 38=RG,26,C65643,0
92821 39=RG,25,C65640,0
92821 40=RG,27,C65642,0
92821 41=RG,16,C65645,0
92821 42=RG,18,C65647,0
92821 43=RG,17,C65644,0
92821 44=RG,19,C65646,0
92821 45=PG,28,C66448,0
92821 46=PY,14,C65861,0
92821 50=PG,6,C66029,0
92821 50=PG,6,C66029,0
92821 50=PG,6,C66029,0
92821 50=PG,6,C66029,0
92821 52=PY,15,C65752,0
92821 66=PG,4,CM2:1,0
92836 79=PG,10,CM2:3,0
92836 80=PG,12,CM2:2,0
92836 82=PG,3,CM2:1,0
92836 83=PG,2,CM2:1,0
92836 85=PG,0,CM2:1,0
92836 86=PG,22,C66531,0
782688 Button changed: bRef=0, Joy=1 (Y), Btn=0, Pressed
782688 [buttons.Learjet 45 FP] 26=PY,0,C1007,1
782688 [DNSCAN] J0.1, B0, bRes=2, Flags=X01, Value=1007[0x3EF], Param=1[0x1], TimeNow=19597812, TimeLast=0
782688 FSUIPC Control Action: Ctrl=1007, Param=1
789615 Button changed: bRef=0, Joy=1 (Y), Btn=0, Released
799989 Button changed: bRef=0, Joy=2 (G), Btn=23, Pressed
799989 [buttons.Learjet 45 FP] 25=PG,23,C66059,0
799989 [DNSCAN] J0.2, B23, bRes=2, Flags=X01, Value=66059[0x1020B], Param=0[0x0], TimeNow=19615113, TimeLast=19597812
799989 FS Control Sent: Ctrl=66059, Param=0
799989 Monitor IPC:03C0 (U32) = 0x800000
809006 Button changed: bRef=0, Joy=2 (G), Btn=23, Released
809006 [buttons.Learjet 45 FP] 56=UG,23,C66060,0
809006 [uPSCAN:] J0.2, B23, bRes=1, Flags=X03, Value=66060[0x1020C], Param=0[0x0], TimeNow=19624130, TimeLast=19615113
809006 FS Control Sent: Ctrl=66060, Param=0
809006 Monitor IPC:03C0 (U32) = 0x0
820862 Sim stopped: average frame rate for last 669 secs = 22.6 fps
825916 System time = 01/11/2013 23:42:00, Simulator time = 23:39:52 (17:39Z)
825916 *** FSUIPC log file being closed
Average frame rate for running time of 697 secs = 22.9 fps
G3D fix: Passes 10866, Null pointers 0, Bad pointers 0, Separate instances 0
Memory managed: 333 Allocs, 333 Freed
********* FSUIPC Log file closed ***********

[Valeryo]

[Pete Dowson]

 

Why are you posting pictures?

 

The log was enough. I'm working it through the code at present. This is an area unchanged since April 2011, so it is not so familiar. I'll get back to you. Please don't post pictures, they don't help at all.

 

Pete

[Pete Dowson]

I'm working it through the code at present. This is an area unchanged since April 2011, so it is not so familiar. I'll get back to you.

 

I found one place which doesn't look right, though it doesn't really explain what I see in the Log file. Nevertheless it is worth a test. Please download this:

 

FSUIPC4921iTEST

 

Put it into the Modules folder and test again. Show me the log as before, please.

 

Regards

Pete

[Valeryo]

Why are you posting pictures?

 

The log was enough. I'm working it through the code at present. This is an area unchanged since April 2011, so it is not so familiar. I'll get back to you. Please don't post pictures, they don't help at all.

 

Pete

 

They help me to be convinced that I made everything correctly.