Ursli80

Hello Pete, i hope you are fine? I wanted to inform you that it was probably due to the Opencockpits (old firmware) Axes Card. I have now installed Leo Bodnar cards on the yoke and the pedals and now it works great. I would like to apologize for suspecting FSUIPC. Best regards Urs

Hello Pete, thanks for your quick answer. Unfortunately, there are probably problems with the Translator. I have assigned in FSUIPC at this time no axes. Neither Yoke, Tiller or Pedals. I just then on the register where in the video to see this movement is seen at Throttle, if I have just pressed my rudder to the pedals. I just wanted to be sure that nothing is assigned and then I noticed this. I saw these things only because I registered the pedals in Prosim (because of the rudder) and wanted to have the Yoke in FSUIPC assigned and the pedals just in the prosim. I noticed big problems with my Ailron and Elevator. See you this video . https://www.mycloud.ch/l/L007EF800B0E64E0851C521322DF90AFD7E363CED55788DADDFA3DE97E0FAABC As soon as I have everything in FSUIPC everything works well (except the Rudder display in the Lower Eicas). I can assure you that I did not assign in P3D and deleted everything there. Best regards Urs

Hallo Pete, ich hoffe es geht dir gut? Leider habe ich ein neues Problem. Ich habe eine neue Leo Bodnar-Karte in meinem Opencockpits-Pedalen installiert. Jetzt zeigt FSUIPC 5.151 unter Joystick Calibration Throttle immer einen Wert und eine Bewegung an, obwohl ich das Pedal überhaupt nicht FSUIPC benötigt habe. Also, wenn ich diesen stark bewege, ändert sich der Wert unter Ruder. Wie kann das sein, wenn ich nichts vergeben habe? Freundliche Grüße Urs https://www.mycloud.ch/l/L006994189D1AAEAEC81B0873F81F8DB2F66D44B2D661519D3A3F9A700B347CE

Hello Pete, i wanted to tell you quickly that the weather radar goes again. I really had to install P3D v4.5. An older P3D version with the latest version (for a "different") simulator obviously causes problems. Best regards Urs

Hello Pete, thanks for your quick response. I tested extra at 3 airports, where it actually rained. This I forgot to mention. Excuse this. This with the official version mor also went through my head. But I'm about to rebuild the PC for P3D V4.5 I will try again afterwards with the beta and then I'll wait for the official version. We'll wait and see. Thank you Pete for your efforts. Best regards Urs

Hello everybody, I have newly installed with my P3D V4.4 FSUIPC 5.151. And drive with Prosim 2.16 Unfortunately, my weather radar does not work anymore, although I copied and pasted the entry from the previous FSUIPC version. Although the radar file is recreated in the Prosim folder, but only with 1KB. Active Skye I have also installed the latest beta. Although still no v4.5 Where could the problem be? Thank you for your efforts. Best regards Urs

Hello Pete, I have good news. it now works as it should. Yesterday I came back to the work, the thought that the download mlgkicherweisse something wrong. That's why I've closed the cache and made the download new. And see everything goes tip top now. Thank you for your help Pete. Best regards Urs

Hello Pete, Thanks for the quick reply. The problem with the RudderBlendLowest with the version "e" is actually fixed. And works well too. I try to explain my problem again, I hope it is better. I have registered my yoke and rudder pedals incl. Brakes (all from Opencockpits) in FSUIPC. This has worked well with version 5.141, except for the RudderBlendLowest "problem, which you have already solved successfully. After I had also updated version 5.141e, all assignments were swapped. Ailron suddenly saved my brakes and so on. I thought it was a small problem and reassigned everything. During the calibration of the yoke I noticed the elevator but that when I pushes the plus values are displayed and I can confirm with set also, but as soon as I pull the yoke to me the minus values from the 0 position are no longer displayed in FSUIPC. So I could not completely calibrate at the Yoke Elevator. When I switched back to 5.141, everything was twisted again, but I was able to rewire and calibrate everything. When I'm back on 5,141 die.ini is still useful? Will be able to attach this tomorrow otherwise. Thank you for your tireless help. Best regards Urs

Hello Pete, Today I have updated to the latest version "e" of FSUIPC. After that, I had some problems. My yoke and rudder pedals were hyped up in the forecourt. So the yoke was registered as rudder pedals and brakes and vice versa. Both are from Opencockpits. I wanted to fix it then I have just reassigned and calibrated. With the yoke, however, I faced the problem that I could not assign the one-sided page (climb / drag), as no values were detected beyond the 0 position. This with the RudderBlendLowest function was, however,. When moving from the Tiller I would no longer Rudder movements displayed. So I'm back at 5,141. I hope you are satisfied with this information? Best regards Urs Goole Translator

Hello Pete, then I was not quite so wrong. 🙂 Many thanks for watching and the possible implementation. Best regards Urs

Hello Pete, thank you for your renewed response and efforts. If this is true, it's okay with me. I was just so sure that this was not the case with earlier versions. Since the Tiller really only the nose wheel steered in my opinion. At least I would not have noticed it honest white. Therefore, I did not come up with the idea in PDF. Thank you Pete for your still very very big efforts. Best regards Urs

Hello Pete, sorry I forgot to mention this. But since this is normal for me, I probably forgot it. Of course I have assigned it directly to FSUIPC and also calibrated in the FDUIPC. Rudder to Rudder and Tiller to Tiller. In the lower DU I see the Tiller and Rudder movements. In the outside view, I also see how the rudder moves when I control with the Tiller. Did I get it wrong? If I roll to the RWY or gate, the plane would only have to be controlled via the Tiller and the Rudder should not move? Best regards Urs

Hello Pete, Today I have set up my Yoke and Rudder again in FSUIPC, since the function of Prosim is just garbage. But now I have the problem that both Rudder and the Tiller controls the aircraft on the ground. The Autorudder function is turned off on my P3D v4.3 and all axes are deleted. What did I overlook? Thank you for your help. Best regards Urs

Hello Pete, I am happy if I could contribute something. Best regards Urs

Hello Pete, I hope you are fine? I promised you a summary of Fly Elise and Warpalizer after my tests. With Warpalizer, the setup is a bit more complicated and with the crossfade, you can bring the brighter places very hard with the so-called Deep Black function. You have to use Warpalizer to calculate the degrees and transfer them to the canvas and align them with a cross laser. Therefore it is more elaborate than with Fly Elise. A nighttime is also that if you want to open the exterior once you only have one of the 3 views, where Fly Elise all nutz. However, on my test with Warpalizer, I had about 5 FPS more on average than with Flye Elise. In general, the P3D V4 seems to need more resources than the V3, or it's just a bug from the v4. Because with the V3 I had always over 25 FPS with my Singel PC operating. So I'm really thinking about whether I should not really install the V3 again. Lucrative if Prosim 737 with XPlane in the V2 fully functional would Währe. So I would change in any case on the X Plane. I hope I could help you so much further? You can always ask me specific questions. Best regards Urs

Hello Pete, Yes Traffic is an extreme power killer. And with me the 25% out. Exactly, one creates three views with the different FOV values, etc. But you have to work with Warpalizer very exactly, damkit it in the picture later has no waves. This is different and better implemented with Fly Elise. I have the Aerosoft Prof version of Zurich. Has London already been updated to Prof? Then I will gladly test this for you Pete and you. Give me a few days, please. Many times I also experienced an error in the update to version 4.1. In the V4.0 I had no such big framrate loss at Fly Elise. The V4 with a Framrate of 18-19 FPS still fly well I think. Best regards Urs

Hello Pete, In fact, our rooms are almost the same size or small. :-) The with the heat I know also, I now open a window, and have a fan mounted, which directs windows the air blows. I have with Warpalizer in LSZH and ASP4 as well as 25 Traffic ca 19 Frams in the P3D V4.1 With Fly Elise it is unfortunately only max. 10th But I'm sure I missed something there. Best regards Urs

Hello Pete, Then your space is bigger than mine. I have about 3.6 x4.0 x2.2 meters available. Yes Warpalizer is at home in Sweden. Man has to work with Warpalizer very very precisely. Otherwise the result is not very satisfactory. Here the link. If forbidden, I remove him. http://www.warpalizer.com/en/homepage-7.html No, I only have 1 such PC. But there really is really only the flight simulator, WarpSoftware and ASCA. Everything else I have on a second computer running. Therefore, my initial network problem :-) Best regards Urs

And here with a colleague in Madeira .

Hello Pete, Yes exactly, I have a Curved Screen with a ca 170 ° representation, weill my room is a little small. I have this with 3 projectors and Warpalizer in operation. Just I am Fly Elsie NG am testing on this. I have pictures attached with a graphic of Fly Elise. My hardware is: Asus Maximus Hero VII i7 6700K 4Ghz OC 4.4 16GB Ram 2x 250 SSD GTX1080Ti FE Regards Urs

Hello Pete, Thank you very much for your encouragement and positive words. You're right. I have before the whole at all no idea had and now have a cockpit with Curved Screen and I have already much deal, than I thought I sold everything again. Think about my network problem :-) I will now really try it with your documents. Because the Translator has become my second best friend. Best regards Urs

Hello everybody, Thank you for your answers. This, of course, greatly exceeds my knowledge. I can not write something like that. There remains only the hope, which Prosim once integrates. Best regards Urs

Hello everybody, If there is already an entry on this topic, I apologize for my entry. Property but unfortunately still no entry found. I would like to have a RWY Bumping sound for my home cockpit, which goes over the Bodyshaker. I have only the problem that I can not play the sound via ProsimAudi, since this can not be attributed of course. Now my question to you. Can you do this via a FSUIPC offset or so? It would then stop synonymous depending on the speed can be played. I use: Prosim Full Suite Prosim Model 2.0 P3D V4 (soon 4.1) Thank you very much for your efforts and help. Best regards Urs

Hello Pete and Thomas I would like to inform you about the state of affairs. Unfortunately, it took some time until I could exclude the addons error, as well as it just allowed my time to test. I have in WideFS now my IP entered. As you are. Furthermore, I have set up on both computers a network over Wlan. However, the prosim and the flight simulator computer not connected to each other. I have on the Tablet I now logged into every network. And so the whole seems now to work without problems. I fly today from LOWI to LIRA and LGKR to LGSM without any problems that the P3D has hung up or problems with FSUIPC were noticed. I would like to sincerely thank you again for your help and patience. Best regards Urs

Yes this is not optimal now is also clear to me. But I live in a very old house and unfortunately it has not changed. I have the two computers not directly connected to each other, weill I have various hardware which also use Ethernet. On the switch I have my two computers, the Sismo MIP, as well as AFT and the TQ. The switch is not connected to the Internet Pete. The Internet I refer via USB WLan embroidery respectively per computer. I am of the opinion I had fixed the IP. Here is a picture of the Ethernet configuration. Un in the and in the Wideclienet.ini, I am of the opinion that I had there under servername my IP eigegeben had. The dan looked about like this: [Config] Server Name = 198.168.1.153 Protocol = UDP Port = 8002 Now, I think straight out that I have installed FSUIPC 5.103 with the update 5.103b Then I could have forgotten to insert these again Pete. This could really be still. regards Urs