Ursli80

Yes this is not optimal now is also clear to me. But I live in a very old house and unfortunately it has not changed. I have the two computers not directly connected to each other, weill I have various hardware which also use Ethernet. On the switch I have my two computers, the Sismo MIP, as well as AFT and the TQ. The switch is not connected to the Internet Pete. The Internet I refer via USB WLan embroidery respectively per computer. I am of the opinion I had fixed the IP. Here is a picture of the Ethernet configuration. Un in the and in the Wideclienet.ini, I am of the opinion that I had there under servername my IP eigegeben had. The dan looked about like this: [Config] Server Name = 198.168.1.153 Protocol = UDP Port = 8002 Now, I think straight out that I have installed FSUIPC 5.103 with the update 5.103b Then I could have forgotten to insert these again Pete. This could really be still. regards Urs

Hello Pete, Thank you very much for the very fast response. Then I have a problem now. Unfortunately, I can not connect my switch to my Internet router. This would otherwise have a 80-meter-long cable or more. So I need to get the internet for both computers via Wlan. Now my question, if I have both computers by Lankabel over the switch in the network running and the computers over Wlan the Internet refer, is this a problem? I would not set up another network over WLan. It is only because the two computers have access to the Internet. No I just make a new computer, because of the crashes of the P3D v4. As I said, I believe the problem exists there with the P3D and not FSUIPC or WideFS. Sorry, the many questions, but I am with the whole network stories still very early. Thank you very much for your patience. Best regards Urs

Hello Pete, Sorry for my late reply, but today the cockpit was still slightly modified. I have never suspected the FSUIPC or WIDEFS causing the crashes Pete, fals this was so I'm very sorry. I do not know exactly where the error is Pete. Today, it was suddenly a picture, but the sound was quite normal. Previously, a stall of the simulator was noticed. All watches run right on the computer. I only change to ZuluTime in the Simulatot No this IP I have not entered. I am using 192.168.1.153 and 192.168.1.156 The port I left extra standard. I have really a few times only the Simulator and WideFS geschtaret to see if a connection comes. Whyski is my Kompas. But why this was tried to start automatically I do not know. I have never entered a command to start this automatically. I must confess in the act I have 2 networks pete once over lan cable and once over wlan. This for the following reason. The Internet I have to cover both computers over Wlan. Both computers are connected via a switch. Wlan network I have set up to use on my tablet the Prosim Instruktiorstaion. And I must also have on the flight simulator because of the Aivlasoft EFB since the provider must be on the simulator PC. How exactly should I proceed now Pete? The with the wireless network I must forget. Just ask me how I have to do this with the EFB and the instructor station. Can I run the EFB on my next computer and then only connect this by Wlan? I'm just about to reinstall my flight simulator again, but will certainly not integrate it into the Wlan network. How exactly should I proceed now Pete? The with the wireless network I must forget. Just ask me how I have to do this with the EFB and the instructor station. Can I run the EFB on my next computer and then only connect this by Wlan? I'm just about to reinstall my flight simulator again, but will certainly not integrate it into the Wlan network. Best regards Urs

Hello Thomas I've just had a strange crash. I was on a flight and suddenly something happened and the plane flew into a dive and the picture stopped. And then again I could not call a Taskleiste and Taskmanager more. Everything should be up to date with the drivers. A Crash.log does not give it. I have added the files. regards Urs WideClient.log WideClient0.log FSUIPC5.log WideServer.log WideServer0.log

Hello Thomas, I have already done this. Thank you nevertheless for the info. I have the feeling it is a sound error of P3D. The begins to stutter and suddenly nothing goes. Even more times the taskmanager and the Taskleoste can then be called. This is very funny. Also the ATC sound does not run over the headphones, although this was on and asusselected. Regards Urs

Hello Thomas Thank you for your tip with the folder release. I had the whole drive released to read and write. However, this did not appear to be sufficient. After I had shared the folder to read and write, it ran now problem-free. Only crashes me now the P3D v4 after about min always off. Best regards and thank you Urs

Hello Pete I still have a problem with my weather radar. This is not for me. I have added 2 pictures to you. One shows you my folder structure where I have prosim. This is on the next computer. Then I took a picture of my FSUIPC entry. I abe this once boeingsystem and tested with BOEINGSYSTEM. Both unfortunately did not go. I was in the prosim folder no radar.bin created. I now have the P3D V4 with ASP4 on the Main PC and Prosim on the next computer. What could be wrong? Thank you very much for your patience. Best regards Urs FSUIPC 5 5.102 WideFS and Client 6.999.4z

Dear Pete, Then I would apologize for this translation error in all form. I have already "read" as far as this with Google Translator went. But unfortunately this works very badly. Yes, I have now fully understood. I had to remove the spaces. So: ASNwxRadarPath = \\Boeingsystem\ProSim737\ProSim737\radar.bin Best regards Urs

Hmm. Now I'm crazy. I thought here in the forum to have read that you would not integrate with FSUIPC 5 the weather radar. Then I must have had this wrong in my head Pete. Please excuse this many times. Would my entry now correct? ASNwxRadarPath = \\Boeingsystem \ ProSim737 \ ProSim737 \ radar.bin Best regards Urs

Hello Pete Sorry the late reply. I'm just bn at the flight simulator to recreate PC with the P3D V4. Okey, I've understood it now partly. The PC name is Boeingsystem. The hard disk has the letter F and has been called programs. Then the entry looks something like this: ASNwxRadarPath = \\Boeingsystem \ ProSim737 \ ProSim737 \ radar.bin Correct? Sorry. In FSUIPC 5 you have the radar yes not integrated. Excuse me. Regards Urs

Ohh I did not synonymous. Thanks for the input Pete. Ahh I understand. I need to actually do the same, just add dea Computer Names. In my case therefore: ASNwxRadarPath =System\ F: \ ProSim737 \ ProSim737 \radar.bin corect? Regards Urs

Hello Pete, In the Prosim Forum I have also created the post, but unfortunately still no answer received. I could solve it so far, however, via offsets. I have a question about Wetteradar function. How do I now create the entry since Prosim runs on the nebnrechner? I have not quite understood this yet. So far I have used these entries: ASNwxRadarPath = F: \ ProSim737 \ ProSim737 \ radar.bin ASNwxRadarBitmapPath = F: \ ProSim737 \ ProSim737 \ RadarPicture.bmp So it ran great. But as the now look must if it runs on the system computer I unfortunately also not. Thank you very much for your help. Regards Urs

Hello Pete Excuse my mistake. I took this from a German instruction, due to my lack of English. So I must have Yoke and the pedals installed on the Main PC and the buttons via FSUIPC offeset set up in Prosim? I understand that correctly? Thank you very much for your patience with me. Regards Urs

I have in the P3D folder under modules only the WideServer.ini and WideServer.dll copied. Should I install something else? Regards Urs

Good Day I have just tried again. Unfortunately, I can not calibrate the Yoke and the pedals in the P3D via FSUIPC, since they are unfortunately not recognized there. I also tried to connect the devices to the PC itself. This, too, did not help. I have seen in the Wild Client.Log the one LUA missing. Can this be the reason? I would help for help very glad, since today someone to fly. Best regards Urs WideClient.log FSUIPC4.JoyScan.csv FSUIPC4.log WideServer.log

Hello Thomas, I have always always changed a couple of times the flight simulator PC and the system PC. Can these entries come from? I have the Yoke and the pedals over a HUB run, but has external power supply. I switched off the USB Power Management. Is it still something else that I can not assign the axes and buttons, if I have connected to the system PC? Regards Urs

Hello, Here are the files. It can be that still the calibration is available from the joke and pedals when I had this at the flight simulator PC. Best regards Urs FSUIPC4.JoyScan.csv FSUIPC4.log WideServer.log WideServer0.log WideClient.log

Hello, Best thanks for your answer Thomas. Yes the cards are recognized as USB / Jostik cards (game controller) in Win 10. There I calibrated them as well since I first thought it was because of it. The pedals and the yoke do not need a SIOC. But it is already possible to have this on a separate computer and calibrate this on the flight simulator in FSUIPC? I can send you dei Files when I'm home. Best Regards Urs

Hello Pete. I would be glad to ask if I forgot something or overlooked. New I have pretty much everything outsourced on from my flight simulator PC which we call him System PC. The whole with WideFS 7 and the latest Fsuipc 4 version 4.968 also worked great. Today I wanted to fly the whole test and a round. I found a problem with my opencockpits yoke and pedals. This I had still installed at the flight simulator PC and noticed that I could not switch off the A / T by means of the button on the Yoke. I noticed that with Prosim737 these USB cards were not recognized at all. Therefore, I have these now s.System PC appended and now these appeared then also in Prosim. However, a new problem arose. I could not calibrate the Yoke and the pedals in the FSUIPC on my flight simulator PC because they are not recognized. I still use the P3D v3.4 as well as Win10 for the test. If everything goes I will re-install the Main PC. Have I overlooked something? Thank you very much for your efforts Pete. Best regards Urs P: S. I have a question about the weather radar. Since I run Prosim now on my system PC, how do I have to enter the FSUIPC.ini?

Hello Pete Since I have not yet a WideFS7 license key, I have to buy the therefore still. All clear now. I buy myself WideFS7 and FSUIPC 5 so I can outsource programs in the future to my Second PC. Thank you very much for your patience with me. Best regards Urs

Hello Pete Sorry again my question. On your side you write, the WideFS7 was installed in FSUIPC5 and you only have to download the link from below WideClient. If I buy new FSUIPC5, I do not need to buy WideFS synonymous to free it To switch? Until now you must both buy both to be able to use both. How is it now exactly? Best regards Urs

Hello Pete, Thanks for your replies. I have a key from version 4, so this will work. Had it just then understood, because it is just a 64 bit version, it must be bought again. Why do I now want to use WideFS? Quite simply, I would like some things like The Overhead, MIP etc on my second computer run and the main computer really only with the flight simulator run. Since some of these things work with SIOC, SC Pascal, I am the opinion I need despite Prosim737 WideFS to it? Then I would simply simply buy WideFS 7 or? Unfortunately, I have to translate everything with Google Translator. Sorry if not everything is correct. Best regrads Urs

Hello Pete I would like to thank you most sincerely for your efforts and help. I have not bought the P3D V4 yet, since I would wait until some addons are compatible like AS2016 etc. I have but still a question now to the purchase of FSUIPC 5. I have it unfortunately still niergends to buy seen. On the support page you have a download link. Is it a free update? I have a question about the wide client. I had missed it at the time. What should I now acquire, so that he works with FSUIPC 5.1? If so many thanks a lot. Best regards Urs

Hello Pete Yes I have disabled Autoruder after the update of the P3D V3.4. And now it is the way it should. Thank you very much for your efforts and support! Simply great! Best Regards Urs

Hello Pete In the logg window, I see that everything is normal. In the display SYS synonymous everything works normally and it is only moved, which I also move. Somewhere the Yoke must go to the Rudder. Unfortunately I can not find it out. Best Regards Urs