reading1871

Ralph, you cannot hide the yoke on the Phenom 100 no matter which of the seven OS's or two FS versions you may be running. D Scobie knows this well enough, I have no idea why he finds it so difficult to answer a straight question.

Fsuipc allows access to many more controls than are available through the FSX controls dialog , please read "FSX\Modules\FSUIPC Documents\List of FSX and P3D controls.pdf" to gain an appreciation of the controls you will have access to through Fsuipc

Just tried that method, works well for me, thanks. Why could Feelthere not have done this, the over the top reflections were critisised when the addon was released but as usual Devs never listen.

I have put them online at dropbox if anyone else wants them https://www.dropbox.com/s/8fzrzkgl65bnfrh/FT%20phenom%20windscreen_Reflections.zip

I have some modified reflection textures, one without reflections but still with the screen heater lines and one with some reflections but much reduced. PM me your email and I will send them

Update Existing Mouse macros do still work if you copy the macro's over along with the corrosponding sections of the Fsuipc.ini file. Only the facility to create new macros has gone for now.

I would install Prepar3D somewhere other than C:\Program Files (86) if you want to avoid issues with other addons going forward. Also be aware that while FSUIPC 4.929 and interim 4929C will install and work in P3Dv2.2 there are issues until Peter gets a new version out. I have found that while 4929C allows me to setup and calibrate my controls it crashes P3D when I try to run Radar Contact and my mouse macros do not work, in fact even the button to create macros has gone from the Fsuipc interface. Lua frictions are also inop. No worries though, Peter is back on the 14th so hopefully soon after he will release a fully compatable version

Hello I would forget about waiting for Goflight to support the NGX and use Stephen Munns script instead, works really well here with my MCP which is Firmware A17. I am not convinced at all that these lockups are caused by the firmware, I have no issues at all and my firmware revision is ancient. The MCP seems to be really sensitive to how it is connected to the PC, you are going in the right direction using a USB card rather than MB ports. Here is what I needed to do in order to get my MCP to play nicely. Added a Belkin 5 port USB 2.0 card which uses the NEC chip, do not use any card with the VIA chip. Plugged the MCP into a Belkin F5U021u powered hub dedicated just to the MCP. The only hubs I have consistent results with are the F5U021u (4port) and the F5U027u (7port) all my Goflight stuff is on these hubs, Max two units per hub with the MCP on its own hub. No lockups here with A17 since setting it up like this. Goflight have been saying for years that a firmware update cures all ills with the MCP, they are still saying this and we are now at A25. I believe that it is more to do with the MCP's power demands and signal path back to the host PC. And do try Stephens script with the NGX, terrific stuff.

Hello When starting from cold and dark, at the point where use the clickspot to introduce the fuel my throttle jumps forward halfway. At this point if you move your physical throttle quickly forward and then fully back the aircrafts throttle moves back to idle. The aircraft does not jump at this point as the engine is still spooling up and full thrust never has time to happen. Try it and see if it helps.

Hello Use the Citations config panel to set the aircraft up to start as cold and dark, reload the CX then run through the startup sequence. once the engines are started and the aircraft set up as you like it, save the flight, use that in future alternatively always start cold (much more fun anyway) One other thing, this CX does not like being loaded after the default flight has been loaded into the Sim, so I always load the CX directly from the freeflight screen, never after a default aircraft. Also have a look at your throttle axis in the windows calibration axis, any jitter there and all bets are off as far a getting the fadec to work reliably.

Hello I had this same problem with the Just Flight Seneca and my goflight units. For some reason known only to themselves, Just Flight coded their own radios and transponder which have exactly no extra features over the default code, talk about reinventing the wheel. Due to the modelled 3d knobs in the VC I could not even swap in the defaults. I had no replys from support on this issue, needless to say it is now deleted and I dare not purchase any more Just Flight aircraft in the future.

Hello Macros work fine for me in the VC, who told you they only work in the 2D panel?

Hello The purpose of this thread is to list the Addons compatible with the Macro facility. please add to the thread any Aircraft you have found to be fully compatible. Any additional notes on gauges in the respective panels that do not respond to macro programming would also be helpful Simcheck Airbus A-300, Totally compatible with macros, all my Goflight units working fine.

Hello In order to keep this thread from becoming cluttered I have started a separate thread concerning Only compatible Addons

*deleted*