ptimale 1 Posted September 30, 2020 Report Share Posted September 30, 2020 Hello Is it possible to create detents in fsuipc, like this article https://forums.flightsimlabs.com/index.php?/topic/14002-first-time-setup-throttle-help/ See answer 14 for the Flaps, I saw in the documentation that it was possible. I do not see the option "DT" in the calibration for the engine thank you I hope you can understand me it's not easy google translation Quote Link to post Share on other sites
John Dowson 126 Posted October 1, 2020 Report Share Posted October 1, 2020 17 hours ago, ptimale said: Is it possible to create detents in fsuipc, like this article https://forums.flightsimlabs.com/index.php?/topic/14002-first-time-setup-throttle-help/ See answer 14 What do you mean by 'answer 14'? Why don't you just follow the instructions in that thread? 17 hours ago, ptimale said: I do not see the option "DT" in the calibration for the engine What is 'DT'? What aircraft are you using? What is your actual problem? For throttle calibration, and axes calibration in general, you should review the section entitled THE EASY STEP-by-STEP WAY TO CALIBRATE YOUR CONTROLS in the FSUIPC User Guide. Quote Link to post Share on other sites
John Dowson 126 Posted October 1, 2020 Report Share Posted October 1, 2020 Btw, for setting up reverse in MSFS, there is also a new control called 'Throttle Reverse Thrust Toggle'. This allows you to use your full throttle axis for reverse (when a set-up with no reverse range) when on the ground. For details, see May be useful or not, depending upon the aircraft and how you wish to use your throttle. Quote Link to post Share on other sites
ptimale 1 Posted October 3, 2020 Author Report Share Posted October 3, 2020 Hello it's not a reverse problem, I followed this post https://forum.simflight.com/topic/90631-chance-to-reverse-throttle-axis-by-button/ and I replied that it works very well I work on the A320 plane I would like to configure throttle percentage on my throttle CLIM = 60% gas FLEX = 80% gas TOGA = 100% gas I print this filehttps://www.thingiverse.com/thing:4405281 It's a Warthog Thrusmaster But hey you will still not understand, what I write Quote Link to post Share on other sites
Pete Dowson 282 Posted October 3, 2020 Report Share Posted October 3, 2020 15 minutes ago, ptimale said: I would like to configure throttle percentage on my throttle CLIM = 60% gas FLEX = 80% gas TOGA = 100% gas If you want fixed settings on your throttle axis, rather than a continuous change, then instead of assigning on the left-hand side of the assignments dialogue, use the right hand side. Define regions corresponding to where you want the detents and assign to AXIS_THROTTLEn SET (n = engine number), with different parameter values: 0 for the idle region, then values between 0 and 16383 corresponding to the % thrust you want for each detent. i.e. 60% of 16383 = 9830 80% of 16383 = 13107 100% of 16383 = 16383 If you want all engines on the one axis, use AXIS_THROTTLE_SET instead. 22 minutes ago, ptimale said: But hey you will still not understand, what I write Not sure what you are getting at there? Pete Quote Link to post Share on other sites
ptimale 1 Posted October 3, 2020 Author Report Share Posted October 3, 2020 thank you I understood now thank you very much the problem is that there is no progressive (linear) between the two points IDLE has CLIM directly Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.