Thomas Richter

Hi, can you please show the FSUIPC5.log file after session fully closed. Thomas

Hi, did you unzip the installer first into a folder? Do you use latest installer Install_FSUIPC5124.zip ? And run in any case as Administrator. Thomas

Hi, it sounds like you use an add-on AC like PMDG which save a big amount of data, not controlled by FSUIPC. As said already, for those add-on AC's it is best to don't use AutoSave. Thomas

Hi, did you run the FSUIPC Installer with Administrator privilegs, right click on it and select 'Run As Administrator'? Thomas

Hi, that's correct. FSUIPC5.124 with latest DLL version FSUIPC5.124a after full installation. Please not that FSUIPC5 requires a new licence key from SimMarket as any earlier version registration key does not work. Thomas

Hi, are the controllers not recognized or not functioning as setup previously (FSUIPC4)? Are they working with a default AC? Thomas

Hi, works OK here, FSUIPC5124a, in both PDK modes (UsePDK=Yes and UsePDK=No). Seems to be something on your side, 0x0BDC with 4-Byte length. Thomas

Hi, FSUIPC for FS9 / FSX + FSX-SE + P3D -v3 / P3Dv4 is only delivered in one version. It doesn't differ between private or commercial use, the only difference between a registered version is the user facilities which are not available in a non-registered version. So private or commercial is the same registration (price) as private and the same product. Thomas

Hi, just copy the FSUIPC4.ini file into the P3Dv4\Modules\ folder and rename it to FSUIPC5.ini. Thomas

Hi, multiple applications can be on the FS PC or on the client PC and communicate with FS or each other via Offsets. Thomas

Hi, when Sim-Avionics uses FSUIPC to interface with FS then that will work on the FS PC direct via FSUIPC or on a Client PC via WideClient (installed on the Client PC). All Applications connect to FSUIPC or WideClient if they use that Interface, but FSUIPC does not connect to other Applications. Thomas

Hi, there is no problem with that but FSUIPC does only see 32 buttons per controller. In FSUIPC5.ini file change this line to Yes [JoyNames] AutoAssignLetters=Yes When you have the first controller setup in FSUIPC the second controller cannot be connected to the same USB port as when the Bodnar bords don't have different names they are seen as the same. So make sure you have both Bodnar boards connected. Also make sure you use latest FSUIPC5 version, FSUIPC5.124a, from download section. Thomas

Hi, as you can see in the content of the If you cannot see the DLL.txt file there is nothing about a DLL.txt file. It only describes what to do if you don't see the file extensions), here dll extension. Also the zip file doesn't contain a DLL.TXT file. You might have misread something. Actual file version is WideFS7141.zip Thomas

Hi, actually on the same PC but inside WideClient in a different classinstance. Just to confirm you use FSUIPC5.124a ? Thomas

Hi, you place it in the [General] section. I forgot I have that line still in, that's why your code worked here OK. Thomas Later: Just tried with UsePDK=Yes and it works OK as well, shows the correct FPS rate.

Hi, your code works correct here with FSUIPC 5.124a in P3Dv4.2 and WideClient 7.141 Thomas

Hi, if you go to Key presses tab in FSUIPC and set a key and select in the drop down 'Heading Bug dec' or 'Heading Bug inc' that would do what you are looking for, if it is a default AC (you didn't state what AC you want to do this for). Thomas

Hi, did you try as well without ObjectPlacer and /or SpadNext and leaving FSUIPC5 active? Did you update or complete install P3Dv4.2? If updated, did you update more than only the Client (Content should be as well updated)? Thomas

Hi, think about how should FSUIPCClient.dll know that there is a change without reading it. The check if there is no change and no further action should be done is in your hand only. Thomas

Hi, first make sure you use latest Install_FSUIPC4974.zip and after installation with the replaced DLL from FSUIPC4974b.zip Please also send your FSUIPC4.log file. Thomas

Hi, the Jeppesen chart you use might be uptodate where MakeRwys reads the used data in FSX/P3D and they are mostly very old. So the MagVar is out of date and Depending on location it can be couple degree. Thomas

Hi, you will need to send then the Runways.txt (MakeRwys log) file and the MakeRwys_Scenery.cfg file for more information. Pleas zip and attach them. Thomas

Hi, as said that is the simple and current solution, inhibit the the axes you want via a Lua script. Thomas

Hi, there is no control in FSX/ P3D to do so. But by using a Lua script you can use Offset 0x32F6 and 0x32F8 to inhibit controls by writing the corresponding Bit(s) in regular intervals. Thomas

Hi, for FSUIPC5 you use the licence info from your SimMarket account. Please copy and paste the details for the registration when you install FSUIPC rather than typing. FSUIPC doesn't need a de-activation to re-install it. Thomas